Search results for query: *

I didnt measure but there was a good 1 1/2in room between tire and inner wheel housing clearance. The outer wheel housing clearance was a little close for comfort, but i know those wheels are what the car was running before the driver's side wheels were stolen. As long as the extra .63...

This shows measurement from inner lip of the 14x8, 4"bs slot I have. The old tire is the same size I plan on using 225/70.

I actually have one 14x8 slot i can put on the back tomorrow and do some measurements from. If I remember the backspace on it is 4". Maybe fhe old tire will even hold air long enough. If it makes a difference my rear end is a 741.

I appreciate the response, and have actually considered going to 15's. But I like the 14's, and have no need to anything other than a street tire. I had several options available when I bought my last set in April. I'm just not sure on the backspacing of this wheel fitting.

Im looking at Coker's 14x8 rallys for the rear of my 67 Barracuda. The backspacing is 4.63 and im not sure if that will fit. Has anyone tried them, or does anyone know? Thanks!

Not much Sunday left, but here's mine...

What would shipping to 74023 be? Thanks!

Gratuitous pic

Slowly moving along, cam bearings were tight, got another set and the second from rear cam bearing had to be lightly honed. Got it to move smoothly by hand with the gear on the cam, and buttoned up the xe256 with the new timing set. Got new rod and main bearings and rings in and the bottom...

If it isnt cranking I'd check wiring from ignition, and wiring between battery and starter. Sounds to me like theres a severed or grounded power wire, a ground wire which has come loose, or a bad fuse somewhere.

Ive been saying TM1, but its a TM5 that's on it now. I think I've decided on the Edelbrock 7176. Between the new cam, and intake the motor should be a lot happier.

Old iron seems like it might be the way to go, just feels weird switching from an Eddy aluminum to an oem. But it does sound like the 4100340/1 is a solid stock intake, and the TM1 definitely not what i need. Ive been reading back through posts and the Weiand 8022 seems highly recommended too...

Thanks for the replies guys, and thanks for the info on the tranny Dano. I dont know what numbers I looked up to come up with A833, but it sounds like an A230 isnt a bad unit. What if i throw another option in the mix? Edelbrock 2176 Enough improvement over stock intake to justify a $250...

New guy here, going back thru the 318 in my new 67 Barracuda. Have it torn down to theblock right now. Had an Edelbrock TM1 Tarantula on it, but i got the stock 4bl with the car. Im thinking the stock intake may be what i should put back on it. What do you guys think? 318, stock heads at...

Thanks everyone, i appreciate the warm welcome! Got cam bearings in, started to do main bearings, but the rear main seal I have just seems small to me. So, I've got another coming tomorrow to compare.

Thats sweet!

Maybe not the same car then. I know he bought it locally, in Agra in 99, and never tagged or registered it. He could have trailered it up your way though. Small older man, zz top beard, retired lineman, used to own a body shop in Ardmore. Im tempted on the headliner/carpet. The guy is...

Was this in Drumright? I bet it was the same car. Needs a headliner and carpet. He told me he got a quote from a guy in Drumright for 300 to do both.

I kinda thought Old Germany went down hill the last several years, but spaetzle beats chicken nuggets any day. I'm in Cushing, for those who dont know its about midway between OKC and Tulsa.

Thanks Dave! I'm still sad Old Germany closed.

Thanks adriver, i feel like I did. Probably the only scenario where wind up with a Barracuda. Surprised me when he asked about the bug! It was a slant 6 auto originally, but I made peace with that prior to getting it. The 318 will do fine when i get it back in. Its a 3 speed A833, and a 8...

Registration, tag, tax, and getting a new title court ordered cost about $500, but i got that done last week, and found some ralleye wheels! Put them on and rolled it out to take a pic. Started putting the locking bead in. Never done that before, and it sucks even with the tool!

Meanwhile....ordered comp cam ex256h kit to take care of the lifter problem. Cam upgrade couldnt hurt either. Should have pulled the valve covers. When I did, I saw someone had ground valves down basically to the retainers. And the lifter, rod and valve that were making the racket had been...

Someone stole the drivers side slots (??) but i got 4 original wheels with redline caps, and trim rings so I mounted tires while hunting ralleye wheels.

Only mopars i have delt with are a 47 Plymouth Special Deluxe coupe my grandpa restored, a 48 Plymouth sedan my dad restored, and a 47 Dodge Custom sedan I had a few years. But all those are stock flat 6 cars, this is a different animal for me. Thanks in advance for any help or encouragement...

Hey all, I'm from Oklahoma, and happened upon this 67 Barracuda while hunting bumpers for my VW. Driving backroads, looking for Beetle field ornaments, my brother saw a couple old guys sitting outside a barn (old smoke house w/ metal building attached) and we decided to stop and ask them...

Im interested. What would shipping be to 74023? Thanks