Search results for query: *

Replaced both calipers (18-4067 & 18-4068) and brake hoses (HSP5563OM). After cold start and car has been sitting for awhile, I have to pump the brake pedal a couple times to get the brakes to firm up. After that, everything is good. Assume I just need to bleed them again but curious if there...

Looking for some front shock recommendations for my 68 Barracuda. Currently, the shocks installed seem to be bottoming out when hitting bumps. Front is sitting lower than stock (about 23 1/2" from floor to bottom of fender) Tires - P205/60R15. Not too sure what other details I can provide here...

Currently running Hotchiks 24385 leaf springs on my 68 Barracuda. Lowered the rear end a bit much for my taste. Any shackle extension brackets, etc. out there to raise it up an inch or two?

Looking for suggestions for a rebuild kit for a 68 Barracuda with disk brakes. I saw a few out there and noticed they are specific for either drum or disk. Aside from the suggestion, what are the differences out of curiously (drum vs disk)?. From looking at pictures, it looks like the idler arm...

Looking for the correct speedo cable for a 68 Barracuda with a 904 TF. Using aftermarket Autometer speedp gauge.

68 Barracuda. I recently swapped out the passenger lower control arm bushing (PITA) and noticed a bad pull to the right after re-installing all of the suspension components. Everything was reassembled back to pre-tear down spec (at least I thought?). I had an alignment done about 2-3 weeks prior...

Any ideas as to what caliper this is? Can't seem to find any information and need to get the correct hoses to fix a brake pad sticking issue.

What's the difference between these two 39 teeth speedo gears? 52068061 and 2538939. They both look identical.

Looking for a 39 tooth speedo gear for a small block 904 torqueflite.

A couple days ago I noticed a ticking coming from my LA360. It's not an exhaust leak so we can count that out. Only happens when engine is at running temp at about 180 degrees. Not present on cold starts and while warming up. Present while in drive, park and neutral at running temp. Ticking...

Looking for a recommendation for a solid engine rebuilder in the Tampa, St. Pete, Clearwater, FL area. I have an LA360 that I want mildly built with some bulletproof components. Pretty sure I have a rod bearing on it's way out. I'm getting a ticking noise once the engine is up to temp.

What is the correct dipstick length and tube connected to block length for the an LA360? After changing the oil and adding 5 quarts, the level is showing way to high.

Looking for website/company recommendation to source the lower dash pad pieces for a 1968 Barracuda.

Looking for a better rear end gear ratio for cruising speeds. Current set up is 410 gears, TF 904 with a 2000 stall and 25.5in diameter tires, which screams at 4k rpm around 70 mph. Ideally I would like to be around 2,500 rpm at 70 mph.

Looking for the correct speedo gear for a 904 TF with 4:10 gears and P255/60R15 tires.

Looking for the correct torque converter for a 727 auto mated to an LA360. Pretty sure this is where my vibration issue is coming from. I checked the balancer and flex plate and it is correct for an externally balanced engine. What all needs to be addressed/determined, if anything to narrow down...

Looking for paint that match or closely match the OEM stainless/chrome look of the trunk trim for a 68 Barracuda.

Looking for a Mopar shop/specialist in the Clearwater, FL area. Hoping someone on here knows of a shop that I can take my vehicle do some engine and transmission work (LA360 / 727 TF).

I've been trying to get my kickdown to engage passing gear to no avail. I checked the linkage connected to the carb and everything lines up perfectly at idle and WOT. However, I noticed that the kickdown lever connected to the trans has no spring load whatsoever to keep it in the forward...

Found a local gas station that has 110 race fuel. Can I run this through an LA360?

68 Barracuda with an externally balanced LA360. Been trying to narrow down the cause of the vibration at around 2200 RPM. Replaced the all metal motor mounts with correct rubber mounts, which helped a bit. The harmonic balancer was old and worn so thought maybe that could have been the issue...

Currently running a Holley Red Electric fuel pump that runs at 7psi. Holley says a fuel pressure regulator is not required with this pump. However, my Edelbrock AVS2 states no more than 6.5psi. Am I safe without one or should I install a regulator?

My current Hedman Tight Tubes are failing. Not too sure how old they are and previous owner is thinking 10ish years but not sure. Left one was cracked bad and a weld job temporarily fixed the issue but the leak is back. Right one is starting to go too. Do these hold up for the most past for a...

Any documentation/reference sheet out there to determine what 360 I have here?

I have been battling a potential internal coolant leak over the past couple weeks. Loosing/low level coolant in reservoir after a couple runs, no visible external leaks, a bit of white smoke on start up, rough idling to the point of almost stalling out and hard start up. Hooked up a pressure...

Looking for an OE strut rod. Mine completely snapped at the forward bushing.

Looking for a good spacer/gasket recommendation to reduce heat soak on my carb. Current set up is an Edelbrock 650CFM AVS2 carb and performer intake on an LA 360.

Installing a new Holley Red Electric fuel pump to replace an existing one that is going bad. I took apart the old one and noticed that there were very small bits of foam around the flame arrestor screen. At first it looked like metal shavings. Took a peak in the fuel cell after all the fuel was...

Replacing my fuel pump with a Holley Red Electric. Requires a 3/8in fuel hose. This will be fed by a dead head fuel cell system. Looking for a hose recommendation to will go from the cell to the pump and pump to metal fuel line. Nothing fancy and just need something that will last. I've heard...

I think I have a faulty starter relay (hopefully). Starting there and working my way down to the solenoid. 68 Barracuda will intermittently not turn over the starter whatsoever. Other times fires right up. Battery and voltage are good. My question is I have seen a couple variations of starter...