Search results for query: *

looking for parking break actuator levers left and right, for a body 8 3/4 small bolt 4x5 10x13/4 drums, these are the ones that go in the between brake shoes and packing plate. Thanks

Hey guys, Need some advice just rebuilt a 440 getting hot after 5 to 10 minutes of start up idling good purple cam AA heads dual carbs. what i v done re-core rad. new thermostat, taken heads to get checked out manga flex ext. took heads off 2 times just to make sure i installed them right. ok...

Hi Guys I have an Intake Manifold #854817-1 Its for a dual carb set up. on a Mopar 440 can anybody tell me what kind of carbs go on it. Any info would be really appreciated. Thanks

Hi, need some help. recent rebuild 340 mild cam, 1406 carb. mopar elec. distributor, timing set at 16. question is when i block the vacuum line for the vacuum advance it runs great but when i unblock vacuum line to vacuum advance it has a hesitation when i raise the rpm. thanks for your help.

Hi, need some help. recent rebuild 340 mild cam, 1406 carb. mopar elec. distributor, timing set at 16. question is when i block the vacuum line for vacuum advance it runs great but when i unblock vacuum line to vacuum advance it has a hesitation when i raise the rpm. thanks for your help.

hi, i have 69 dart 340 and looking for the size of the spacers that go through the alternator mounting bolt there is 2 a small one and long one. if any body knows how long they are please let me know. thanks.

just got a MP distributor new. i have the motor on top dead center and the oil pin gear distributor slot pointing to the front of motor. ok the old distributor was ok but i decided to buy a MP DIST. The car ran OK pulled the old out and the new MP rotor will not line up with the number 1 piston...

Hi, leaking trans fluid from speedometer cable is there any type o-ring or gasket i need to get to fix leak. any ideas will surely help. thanks.

hi guys ok i have a 340, j heads, 1406 edl, edl340 intake, mild cam, elec. ignition. i want to do this from the carb. how many turns on mix screw to begin and what should i set my timing. do i need to plug vacuum when timing. the engine was rebuilt doesn't even have 200 miles on it. can...

hi guys need some advise. elec. ignition, timing set at 18, ld340 intake, 1406 carb, mild cam. runs good at idle but when i put it in drive has a stumble or misfire almost wanting to shut down. car runs good at cruising and at highway speed. where should i start looking. any input would be...

need help on this timimg issue. timing set on 8 before but it jumps hi and low like 3 numbers at idel. its a 340 with ld340 intake, 1406 carb, 360 heads, mild cam, just built motor. where do i start looking. thanks

ok guys i have a 69 dart 340 ld340 intake mild cam and 1406 carb. electric choke seems to work. starts when cold but if it truns off before warm up wont start back up unless i por some gas in carb. when its all warmed no problems what so ever it starts right up and runs good when i go for a...

hi guys ok i have a 69 dart 340 with ld340 intake and a 1406 edel. question is what type of air cleaner can i use not to much hood clearance. i had a moper performance air cleaner for this set up, does not clear the hood. is there anyway i can still use the MP air cleaner? what type do i need...

Hi Guys i have a 69 dart 340 with 360 heads and mild cam just for street use and week end use, my question is i have an ld340 intake and edel 1406 what kind of spacer adapter or gasket is good for this set up. is edl heat insulator gasket #9266 all i need is there any other gasket needed,dont...

hi guys well all most ready to give up on these headers. this is what i have 69 dart 340 with 360 heads and its a 6 k member with the conversion mounts for a 340. just to much hammering i knew i was going to be doing this but OMG THIS IS BAD. steering column not bad but where the idler arm...

hi guys dum question but i need help looking for a fitting 90 degre 6 an to what size i have a stock pump on my 340. thanks for your help.

:dontknow: need some help i had a 318 in my 69 dart which was 72 date code on block. now i just built 69 340. my question is the three roll crank pulley does not fit, one bolt hole does not match. now what is the correct pulley what should i look for, the car has power steering, timing mark is...

Hi everyone doing my first rebuild on my 340, my be a dum question but sence this is my first rebuild just want to make sure. does the installation if the oil pump take any gasket or o-ring. Thanks for info.

Hey GUYS My question is whats the install on these looks like the notches on these rockers are the same. do the notches go in the front or rear. any info. thanks

hey guys, this may be a dum question. i am replacing my sb valve covers with the mopar performences valve covers and the air cleaner black wrinkel so what do i do with the pcv.

hey guys, just got my 340 from machine shop they did the short block now i have to assemble the rest. This is my question what type of thread sealant should i use on the bolts there are so many sealants out there. any info would really help.

Hey guys quick question, whats the engine color on 69 dart 340 engine? red, orange any # or where is the best place to get the right paint would help. Thanks

i have ld340 intake and 1406 ed 600cfm. just picked up for my 69 dart 340 mid build. what my question is, will this carb. work on this intake if so what type of gasket or spacer do i need? any info would be really helpful thanks.

looking for timing chain cover for a 69 dart 340 with the timing mark on driver side. needs to be in really good shape, pm me with pics or email. Thanks

Hi Guys Going from a 6 cyl to v8 340 do i need to change out the center link to a v8 center link or are they the same? Thanks

hey guys, have a 69 dart with sb installing headers also a starter any part numbers or no the year i can pull a mini starter off of at the junk yard that would fit the dart.

Hi guys I have a 340 that is being rebuild, the build is petty much stock build the onlything is i am using oem mopar adjustable rockers and running a hyd cam. need to know what size cup push rods to use and where to get them or part #s thanks for your help.

any body going, need more mopars out there kicking some butt.

hi guys will early 360 heads work on a 340 block? the heads are stamped 360 on the inside. thanks for your help.

hey guys, thinking about adding a front sway bar its a budget build car v-8, weekend car with no sway bar tabs. can tabs be welded on lower arms? and what about the addco 150 sway bar are they even worth buying?