Search results for query: *

See you before 11 today.

I will take it. I can leave here at 9, probably be there before 11 AM if that works. Just let me know.

Do you know if this is a 5 or 6 detent valve body?

Ok, I can pick it up this weekend. Sunday afternoon/evening works, but if Sat is what your open for, I will make it happen Sat.

That sounds like the one. I have the other half on the driveshaft.

Does it have the weird output yoke on the back? Can you post a picture?

Longwood, 20 min North of Orlando

Will take it. Let me know if you/it are available on the 12th.

Wonderful. I have a 1967 904 out of a 273 Barracuda that was working when pulled if you want to trade. I am out of town till 4/11, but can pick it up after that. Will PM you with my information.

Looking for a 1965 cable shift 904 transmission. Going into a 1965 Barracuda with 273.

Thanks everyone for the information, I ordered a silver one, going with somewhat original style. I will let you know what I think

While I am thinking about it, is there an aftermarket tach that would fit into the center of my dash? It is currently blanked out.

The black top half of mine looks ok, the bottom half is missing a lot of chrome from the plastic. This would be easy to put in, and fix the worst of it. I have seen remans for 5-600 dollars, and this isn't the car to put that kind of money into a dash bezel. This is listed for the rallye...

Has anyone every bought and installed one of these? fit? finish? durability? Mopar A Body 67 Barracuda Rallye Dash Lower Trim Overlay - MATTE SILVER

The metal work on the entire car is done, this was discovered when I tried to put in a gas tank. I guess I will have to cut what I have to cut, and then add support where needed. I added torque boxes and put agitational metal in front of the valence that connects the 2 frame rails together. I...

Thanks for the info. I have the new gasket on the way. The trunk is all welded in, actually the car is near ready to paint, so I will be doing tactical adjustment to make it work. It seems all the first year series Barracudas have some interesting issues, 64 1/2, 67, and 70. I have very...

Thanks for the heads up on the AMD part. I installed the AMD floor, and used the existing one strap with a new gas tank and it worked/fit fine. Have not tried to fit the filler neck in yet, but need the gasket before fitting that in.

I am putting a 1967 Barracuda fastback back together. I put in a new trunk floor from AMD and take note of the hole for the fuel neck, some sort of polygon. I bought a fill filler neck gasket to seal around the hole, and it is no where close to fitting. Maybe it is for a rear filler neck on...

I may just rotate the pins 180 degrees that are in there. They have some wear on one side, but the hinges are not egged out. I looked at my 1970 Cuda, and it has the same setup, same hinges, just flipped. Mopar being cheap and reusing stuff again.

Thanks for the information.

I am cleaning up and painting my hinges, and it looks like there are 2 left side hinges, with one installed upside down on the passenger side. This is an early production 67 fastback. Looking at what is for sale, there is a L and R hinge, but mine look the same, other than one is installed...

Thank you. Are there any stops that center or hold the trunk other that the once you showed, or do they just depend on the locking mechanism?

Does anyone have the rubber bumper stop locations or diagrams for the trunk, hood, and door of a 1967 Barracuda fastback?

I think I found a working 1965 908 with cable shift, and will use it. Thanks for the response. Hopefully I can complete the deal.

Does anyone know if the transmission in a 1967 Barracuda is the same length and configuration, other than the cable shifter, as a 1965 Barracuda, both are 273 engine cars.

I have been looking for pictures and not found one yet. I am assuming the bucket is mostly straight up, and the bench seat is S shaped, like the roadrunners/etc.

I am looking at upgrading the 904 automatic on my 67 barracuda to a 4 speed A833. The petals/etc seem straight forward, and welding in the hump is not a problem. The 340 engine is all set with the bushing in. The question I have has to do with a shifter in a car that came with split bench...

Thanks. I used this to check with Eastwood, and I believe they have this available, although it does not show on the web site for OEM paints.

I have a 1967 ZZ1 Gold Poly paint code that I am trying to get a recipe that a paint store can use. They say they don't have it in their book. From what little I know about paint, I believe there are a couple of standards that provide colors/amounts that are used to create a color. This is...

I have a 1967 Barracuda Fastback that I have a 340 TA motor that I am putting in. I have not settled on a transmission yet, looking at either an automatic 46RH 518 or a manual A833 4 speed. Car came as a column shift automatic. I sort of like the idea of the manual, but the auto would be...