Search results for query: *

Thanks fellas!

Can someone tell me if the upper & lower stainless trim on my standard '71 Duster grille will fit on the OER 340 "sharktooth" reproduction grille? Thanks! Rod in Wi.

I see that Dante's Mopar parts offers a fiberboard 2 piece headliner for '72 & up Dusters.He also sells the plastic replacements.Just wondering if anyone has seen or installed one of these new fiberboard replacements & if so,how is the fit & finish compared to the plastic headliner?

My '72 Duster was built with a 3 speed stick that I replaced with a 4 speed.I also added the reverse light on the dash. My question is where or how did the factory connect the dash light to the harness? Thanks!

If you decide to do it yourself I would highly recommend Tom Hand's (VOETOM on this site) guide book for servicing Tourqeflites.

I would like to buy a new fuel filler pipe for my '72 Duster but can only find one for '70 / '71 with ECS or '73 / '74 with folding rear seat,or for '75 / '76. Can any of these be made to work on a '72? What changes were made between these years?

Make sure the fuel pump push rod isn't worn...

Here is a link to a thread with more info on this car. It was started by the guy that I bought the car from. 1966 Plymouth Valiant 100 Ken's 66 Valiant has Subframe Connectors!

Mike, If you use the driveshaft code from your broadcast sheet & Galen's vol I book it will tell you the ring gear size that was installed at the factory.

I'm looking for help decoding the broadcast sheet for a '66 Valiant 100. It's a 273 Commando/4 speed / 3:91 SG 8 3/4. No radio,heater delete,seat belt delete. There is no factory seam sealer or sound deadener. I'm pretty sure this car was special ordered for drag racing,although it was never...

I have a '66 V-100 with an 8 3/4 3.91 SG that looks to have been there from day one. The build code for the axle is 173,I can't find a reference for that # in the white book,but the 41 code for the pinion would seem to be correct for the ratio. I will start a new thread on this car & ask for...

I am looking for the Mopar part # for the front license plate bracket for my '73 Duster...the parts list I used doesn't show it (or I couldn't find it).My car did have the bracket on it at one time but it went MIA...if I had the part # I could try a search. Thanks! Rod in Wi.

I need a front license plate bracket for a '73 Duster,needs to be rust/pit free.Thanks! Rod in Wi.

I'm looking to buy one 440 emblem like the one pictured,NOS or nice used,must be OEM Mopar. Would also be interested in a pair of "440 FOUR BARREL" emblems.Thanks! Rod in Wi.

Two years ago I picked this up in LA & drove it to the the top of Nova Scotia,then back to Wi. Last year the wife & I drove it Fogo Island Newfoundland.I also use it as my daily driver in the summer.It still has points & drum brakes!

Would the 383-4 with the 3 speed in a 4 door have a floor shift like a road runner or would it be column mounted?

Check with DMT

340 Buick

Here is a nice 1407 Edelbrock 750,works & looks great,I bought this new,the only thing I ever did to it was to add an electric choke,it is still on the car so if you are local (Neenah,Wi) you can hear it run,just bolt it on & go.$165 shipped in lower 48

Every 6340 TQ that I've seen has been stamped over a 6319,I have 2 of them & 1 of them is NOS in the original box.

1972 Duster

Can someone tell me what was originally used to seal between the front fenders & aprons? I seem to recall something that looked like adhesive backed cork stuck on the apron part? If someone has a photo of a car without a fender that shows this stuff that would be very helpful.Thanks!Rod in Wi.

Would you sell the outer brackets & bolts separately? Tried to PM you,your inbox is full.

I'm in need of a driver's side tail light lens for my '73 Duster,NOS or really nice used.Thanks! Rod in Wi.

I need some advice on converter choice for my 727.My car is a '67 Coronet,stockish '74 440 HP with a Comp XE262H (218/224 @ .050"),Edelbrock CH4B intake,& an Eddie 750 carb ,2.94 rear with 27.4" dia. tires. Comp says a stock converter will work ok with this cam.I don't have a stock converter but...

Hey Jeff,Thanks for checking that for me,I really appreciate it! Rod

Thanks Jeff, now I know my bearing is the same.How is the fit in the extension housing & the output shaft? The shaft diameter on mine is about 1.376".

I'm looking for dimensions for the output shaft bearing for my '72 727 TF. The bearing that was in the trans has about .001/.002" clearance between the tailshaft housing & the outer race & about the same between the output shaft & the inner race.It is a metric bearing,35 x 72 x 17. Is this the...

Some 727's have drilled & tapped holes on the tailshaft housing for a damper weight but mine doesn't.I would like to add these to my trans so I can mount a damper. Does anyone have a factory drilled & tapped housing they can measure for me? I also need to know the thread size & diameter. I...

Do I want or need these "red" clutches and Kolene steels in my 727? It will go behind a stockish,daily driver, lo-comp. 440 with a 220@050" cam,HP manifolds,750 AFB,2.94 gear. I'm using a Transgo TF2 kit set up in the mild mode and a TCI Breakaway converter ,also have the 3.8 lever. It's time to...