Search results for query: *

Is the new FBO system your referring the one that was released in July of this year 2011.The billet cover with HEI module inside.I bought one in July of this year.After running it for a while ,about a month started having issues with starting hot.Before I condemned the unit,I had a friend of...

I recently had issues with a MSD 6 controller.I replaced it with the new module that you make reference to from FBO.It does not need a ballast resistor.It is the same size as stock mopar module and uses the stock mopar electronic harness. My engine is a 340,with the mopar 280 cam,Holley 650...

Yes.I run the same cam in my 340 that you use.I also did the headlight relay upgrade.With the alternator and relay upgrade my lights my lights do not get dim.It works great at slow cruise. With lumpy cam 13.7 volts under load is low and lights will get dim.The stock alternator has to be rev to...

You are correct that the blue wire is the sense wire and the green wire is the ignition,that is how the plug is wired when you buy it.It the post I mention to remove the wires that come with the plug.There is no need to splice wires to that connector.Look at picture number Three, all I did was...

This is a quick overview for installing a Denso Alternator on a small block Mopar. This installation is based upon the Amp meter bypass. This kit is designed to work with a non-AC car; you CAN use it with an AC car only if you change the pulleys out to a non-AC and use an AC kit that changes...

In order to fix this, this is what you need to do.You need to loosen your instrument panel so that access the plug at the back of the instrument and operate the turn signals at the same time.You will need a test light.Operate the left turn signal,remove the bulb holder and take the test light -...

On a 1970 Duster there is a turn signal fuse right side of dash around the glove box area.Not sure if a 1973 is the same.Hope this helps.If not you may need to locate a wiring schematic for your year car.

On my 1970 Duster the parking lights have a similar set up.Keeping in mind that grill is plastic and the park lights is mounted to the grill.The lights need to be grounded in order to work.So you need to run a ground wire from that tab to radiator support area.That needs to be done to each park...

I have used the Year One harness.As been stated its plug and play.Whatever you do make sure you compare the new harness to the old.For example on my 1970 Duster it has factory A/C.I had to use that part of the circuit and plug into the new harness.Also Year One was also considering updating the...

Yes, the people at Red Line Gauge are excellent; great work. In addition to the volt/amp meter conversion, I had the complete instrument cluster rebuilt by them. In the picture you will see the Tach - that was a blank plate where they installed a custom Tach. In regards to connecting the...

This the fuse box for 1970 Duster.

The company that has the adapter is called American Innovation Corporation.There minium order is 25 pieces.Here is the link http://www.aicorp.us/

.In my 1970 Duster I have replaced the amp meter with a volt meter.The red and black wire has to be connected to complete the circuit.In the Oct 2008 Mopar Action page 70,they have a article dealing the charging system.

On a 1970 Duster there are three connections at bulkhead inside the engine compartment.You have the engine /forward light harness that plugs into two of the connectors.The third circuit being the wiper,backup light neutral safety.The harness you are in need of is called engine forward light...

Yes the bearing is available.On my 70 duster it is an automatic column shift.There is one bearing at upper part of the column.Then there is a plastic white bushing at the base of the column.Before attempting this repair I would suggest locating a factory service manual.I would pull the column...

I have a 1970 Duster with ralley gauges. It is still apart.I am going off my memory .The ground circuit should be your negative cable to engine block with pigtail to engine compartment; heater has a ground circuit right side rear of engine.On a A/C car the heater box is grounded right front...

I am not sure if the information is going to be in the book but MSD has a wiring diagram and tech note book - part # PN9615. You can call the customer support department: 915-855-7123. The book is free. I have one coming because I am going to be installing the Mopar version of the MSD on my...

I am currently working on a 1970 Duster and have looked in to the variety of wiring harnesses available for this vehicle. Year One is going to be the main provider of a factory harness because they bought up the patents for Chrysler wiring. Even if you were to contact the company that makes...