Search results for query: *

Is this true about forged pistons in general?

www.stewartcomponents.com

Sorry I got here late, lol, yeah the frt T-bar socket/arm would have to be frozen together...that's the only thing that can do that. Either by rust or damage/deformation of the arm. Those West-Coast guys don't know what it's like to deal with that stuff, lol!! I pulled the K-frame, arms &...

Don’t know what a v65 is? An intercepter? Burned off stock tires put a set of Michelins on it and ground the steel nubs off the foot pugs. Like I said had a plastic body filler knife in my back pocket to scrape my pants out

68 up heater control pin 67 (and 68 to 71 dodge truck of all things)

Here's some info regarding the terms 904, 998 and 999. In the Chrysler parts catalog under group 21 automatic transmission parts only the 904 is listed. To determine the number of disc used, you must have the PK number. In all the Mopar performance books the 998 and 999 are covered but not in...

the frustration is understandable. and while the squeaky wheel usually gets the grease, it may come at a cost of sloppy work or cutting corners here. while i don't think you're to the point of: "let's take this to court"; i do think that you need to escalate it. i would start with a phone...

For sure I’m going to replace hoses and what not asap thank you for the reply.

For sure I will. Does it make any difference if it’s mainly only stalling in gear at idle? Could it be a tuning issue idle screws/speed screws etc? Not sure why that would flare up after getting gas though but just checking. Also may have sounded worse/stalled faster with the lights on etc...

VERY ROUGH first draft from photos I estimated the large hole is 3/4"

Not sure when those came in but they do not use the clips. Until this thread I didn't know there were two styles. Alan

Perfect, Thanks

I just did a fuel system service to my Ford truck. Although not a Mopar, it had some OLD sections of rubber supply hose and the one that connected the fuel sender to the main supply line was VERY soft. I was having an issue where the truck would stumble and fall off and almost completely die...

Here is the top part of the pins

It's an outright buy of one of their rebuilds, a no core deal. They don't have my transmission. There is no 'take charge' to it. I don't want to hear from them what I heard from the local shop, 'Here's your deposit, thank you for not doing business with us.' My car has been sitting since I...

The part that prevents the door from opening too far and holds the door open. Some call it a stay or check.

OK. You are NOT whining. But you have to take charge of the situation. Go to the shop and demand to get your and your transmission back. Threaten them with small claims court if you have to. They should back off on that. From what you have said, they know they will lose. Then contact Brewer's...

Qtip and great for that stuff

I helped a friend restore a rough 65 Impala SS 396. He bought PPG BC and CC paint. I sprayed the door jams, backs of doors, back of hood and back of decklid. Then I helped him assemble the car. Right before I was ready to paint it, his wife said something that pissed me off so bad that I just...

I am doing a 4 speed conversion in my 72 dart and I ordered the m&h backup harness. I have the wiring figured out for the rear and dash mounted lights but there are still 4 wires that I can not see what they are supposed to connect to, 2 are under the hood and the other 2 are underneath down by...

The short answer is the 7.25" would've been std. equipment for Slantys & 'teeners, You could always option up in those days, so finding an 8.75" behind them is surely possible as well. 8.25" rears didn't appear 'til '72-'73, so there's -0- chance that was an option in Your prospective ride...

Call me a necromancer!! So I have a similar problem and the rigid exhaust thing seems to be possible. I have manifolds to welded pipes out the side. I have also lowered the dart 1" all around with blocks and cranking the arms. Under acceleration I get a rotation based TING TING TING, I was...

I used this same supplier. Had great service from them and got everything needed in 1-stop shopping there. Highly recommend this supplier!

What are you calling a "Door Check"?

Hey Del. good to see you back. The machine is an old school Lincoln Tig 300/300 and arc welder combo, probably 70`s era. Not even compatible for a wire feeder afik. One of those massive 800lb. hunks. Only thing the roller motor and welder share at the same time is common service ground. Tig...

Yeah it's pretty big, just about the same height as my ram 2500 tires. A 30 inch tire would have fit perfect in a s/s wheel arch . I like the wheel where it's supposed to be not moved back, it will be more work this way but it will be how I like it when done. It should hook well and do a good...

What size pickup? Also, is there a hole on the top?

Crazy how different they are in reality from advertised. Those are some meats!

Real size 30.60 - 13.50 -15 Hoosier says 29.5 - 11.5 w 15

What size tire is that again?