Search results for query: *

I use those and don’t get any droning at all 2 1/2from header collector right through the back . Nice and not loud but when you get on the loud peddle it barks .

Will be fun pulling 5-7 plugs out with that cross over or burnt leads ..

I understand but that’s like a few of my engine components said to fit x engine you need to make alterations for it to fit . It sucks when you shell out your hard earn and things don’t fit as they should. Hey that’s hot rodding !

Funny thing the place I had my dougs recoated after tube reconfigurations said to me he advises everyone who enters his shop to buy them bare, fit them up make your adjustments than get them coated as this applies to all brands of cars .

Moa what worked on mine as I had to make some clearance for the drivers side torsion bar was I used a long 1/2 inch extension bar ( socket set) Layed bar across the 3 tubes and gave them a hit it came out well and looked Like it was meant to have the indentation.

I feel your pain when I brought mine in to get recoated the chap said never buy em coated test fit them and make your adjustments to them than get them coated.

Looking at my mount pic reminds me I need to change those bolts little short on a few. I forgot to address that when I was fitting them.

Here you go I hope this helps manual steering though. This is a 360 so drivers mount will be different.

Moa when I get home I will check my one and take a photo as I am running the same mounts . Here’s a photo front shot I put up previously . I will take a top view pick tonight.

I was using the biscuit type than switched to the Schumacher poly mounts which are approx 20mm taller. Pass side fitted like a glove cleared everything .

Nice to know that now .:rofl:

Ok I purchased these in Aus so I didn't have to pay on the shipping still $650 large as you can see on the pics no matter what I did raise drivers side mount pull steering column away it just didn't cut it, and the amount of area which needed massaging just was an eye sore and I was sick in the...

I will post some picks up tonight as they are on my laptop the mods I needed to do as no 7 tube was hitting steering column and needed to be hit half the size to make it fit I ended up cutting sections on tubes 5 and 7 and swapped them around couldn’t believe how much clearance it gave me .

With the Dynomax mufflers were they the super Turbo or the Ultra flows ? reason I'm asking is I run the super turbo's now on a 2 1/2 in system with balance pipe and don't get any droning where as before I had some 10in turbo mufflers don't know the brand ??? which would drone pretty bad around...

Just a bit overboard Lol I cringed with every blow ! no choice every time we lowered engine to check clearance it kept on hitting, I even shorted that little bolt that holds the collar in place to give some clearance, moved column has far as it allowed me maybe if I had an universal elbow...

I've taken some snaps off mine , pass side fitted like a Glove , the dark side I needed to massage no 7 tube to allow fittment, and needed to clearence tubes for the 1.03 torsion bars drivers side only. Moved steering column over as far as it allowed me . Was easy to install while bars and drag...

Thanks

Gnats ??? is this a hillbilly thing like claw dags ??? fill me in.

Pishta what about cutting a piece of pipe in half slipping it over the hole than using these 2 at each end.

I had to clearance the drivers side with the 1.03 bars some thick Tubing and some love taps gave me the clearance and needed to do the rear tube because of steering column even though I moved column over it wasn't enough. Pass side fitted like a glove.

when I got my exhaust done last week prior of sending it there I asked if they would fit the Dougs 453s and do the complete system aswell , they wouldn't have a bar of it. I ended up fitting the headers while I replaced the torsion bars than sent it down to get the rest of the system made up.

Nice pieces and hassle free in fittment but @ $950.00 US Convert to Aus dollar- $ 1300.00 + 100-200 shipping + custom fees and all the bullshit because its over 1 k to land them. Might settle for the D 453 and get them coated here.Cant stop checking them out i can picture these on my ride !

With these figures when they ran the headman, TTI,Hookers on what engine did they run these on to get these figures.