Search results for query: *

Did the whole floor, covered with press on deadener. Also, hit the surface rust on the interior roof with a wire brush and couple coats of por-15.

I used POR-15 on the floor of the Duster. Very pleased with the result. A little goes a very long way. Pat

Love it!

I8Nemo, Do your thing man. I think your ride looks great, and would still look great with the wing. Being different is not a bad thing. Opinions are like belly buttons. Be well, Pat

Hey thanks WymanV. Much appreciated. Pat

Anyone? ....Anyone? ....Bueller?.....Bueller?

Hey Folks, Just finishing up a little project to repair missing mounting tabs (4 gone on 1 side and 2 on the other) for the tail light assemblies on the Duster. When removing the assemblies I encountered a "hodge podge" of nonstock hardware store self tapping screw in varying lengths and head...

Another satisfied POR15 customer here.

Maybe hit them up with some POR-15 or similar product? Pat

Not sure about new ones, but I scored a pair a nice used ones for my Duster by listing it in the Wanted forum. Think it took about 8 minutes for an awesome FABO member to help me out. Pat

Looks Great Man! Pat

Thanks again man.

Hey thanks 6pk2go. That helps a lot. What type of adhesive did you end up using? Be well, Pat

Hi Folks, I hope everyone is ready to enjoy a great 4th! :cheers: The girls and I have been taking advantage of the long weekend by gutting the Duster, welding up some cracks in the floor and preparing to fab up and weld in some frame connectors. Off course we'll find time to smoke some...

Hey Plumkrazee, where did you source that seal? Thanks Pat

Same here on Prep. Have had very good results with POR15 products.

Thank you all for each of your input! Well, hit the garage after work today, with a much calmer demeanor :glasses7: and am glad to say I got the hood square away nicely. Started with 76orangewagon & torkflight's suggestion. Funny thing is it worked! Thanks again guys. After that I fiddled...

Thanks for the reply Trailbeast. Much appreciated. Rubber bumpers are in place and hood had equal space between the hood and fenders prior to me loosening the bolts that attached the hood to the hinges. I created the gap when "fixing" the high corner. It sure looked like an easy fix anyway LOL...

Hey Folks, I fixed a hood alignment problem on our 72 Duster, i.e. rear driver side corner of the hood was sticking up above the fender. Good news is I got the height corrected, problem is the entire hood now sits too close to the passenger side fender :banghead: After much fiddling, and some...

Nice looking Duster you have there Burl. :D Pat

I Have had very good luck with all the POR15 products I have used. Pat

LOL...That's a blast from the past Paul. It was $99 when I had them paint an old Firebird. Like you said, "served it's purpose". I was 16, broke and car had like 4 different colors of primer. Pat

One of the PO's did this, we like it but after we finish the body work are considering painting it all yellow except for the scoop and go-wing (keep black). Then add factory stripes and emblems. Pat

Good job! glad you go it sorted out. Pat

Not a diagram, but this thread helped me get my installation done... http://www.forabodiesonly.com/mopar/showthread.php?t=35796&highlight=water Hope it helps you some.. Pat

This might help brother...Go tme through my installation (I had nothing, no wiper motor pivots, armes etc LOL) http://www.forabodiesonly.com/mopar/showthread.php?t=35796&highlight=water Pat

X3 It's hard to get at em, and laying on the floor under the dash is hard on the back. But an easy fix once you get the linkage out. I assembled the linkage outside of the car, then snaked it up under the dash and connected it to the motor and pivot arms. You may want to take the time to...

Got mine on Ebay 73Dartswinger. Not from this seller, but the same bushing. Do a search for 73 plymouth wiper linkage or bushings, I'm sure you'll get a hit...

Thanks for all the additional info folks. Much appreciated. I'll post up pics of our progress in our restoration thread. Be well, Pat

LOL Trouble maker///:joker: