Search results for query: *

try partsmix https://www.partsmix.com/categories/a-body/bolts-screws-fasteners.html?page=9

Fat fingers while scrolling

I guess I’ve been a little careless in my scrolling and hit the disagree button by mistake and not noticed. Sorry for any confusion-no disagreement here

Spec's? primary dia. & collector dia?

great idea! how about some installed pics?

Thanks for the pics. I was curious about the area btw the t-bar & frame, i think a pipe goes thru there. Here’s some shots of where I’m at

That's exactly what I'm in the process of doing but I don't have the headers yet so I was looking for some pics of 66durgederp's rerouted lines to clear the headers. And don't call me Shirley!

I know this is almost as year old but i'm finally getting around to my brake lines, Any pics of your rerouted lines?

Hookers usually have the mod # stamped somewhere on the head flange.

here's a couple with the engine installed, check the next page too. Update on My 64 Dart project

check out the pic in this thread early a k frame spacers?

I'm with ya on that. The next decision is coated or uncoated. it's cheaper to buy them coated then to have it done afterwards as long as there are no mods needed to make them fit. and if I'm going to do a trial fit the doug's probobly go in and out alot easier....food for thought,.....I'm still...

If my research is correct Doug's 63-66 a-body-slip tubes, 2 3/4' collector. 67 & up no slip tubes, 3" collector TTi- 63-66 no slip tubes, 3" collector, 67 & up # 7 slip tube, 3" collector.

I'm going thru the same dilemma for my 64 Dart. Doug's are a bit cheaper if you can get the AZ 20% off deal but the smaller collector and slip tubes bother me. I had hookers on my 68 and never could get the slip tubes to completely seal. they do make for an easier install though. The TTI's...

By how much? would it possible to get a measurement from the rear air cleaner stud to the hood bars of firewall? I do plan on a torque bar/engine strap on mine also. Another q, does it fit under the hood? thanks, Gary.

Here's a couple of pics of what i want to use

] I like Dartmans idea of using gas struts if I have to. The AC assy i have is the AAR/TA one that Rustycowl described, I'll try and get a pic today. 72 Dart, does that one fit?

Guys I'm working on a 64 Dart(currently /6) that I'm putting in a 340 with a 6pack. I'm wondering if the stock T/A air cleaner will fit in the car. It looks like the hood torsion bars might inerfer. Does anyone have the setup in an early A? Or can you give me a dimension from the rear carb stud...

Thanks Here's the two other pans I have. The greasy one is the 68 340 pan

Just kidding about the cut-off wheel... heater core and wiper motor are coming out anyways.. besides I wouldn't cut the shaft I would cut 2 sections out of the arm knuckle then it would just fall off!

Oh yea, I shot it with some liquid wrench, all out of pb right now. torch or cut-off wheel next

also looked underneath and didn't see a clip. not the best photo but i did use a mirror to look closer

actually there is, the post goes thru the wiper arm

Thanks for the link, that help give me some more ideas I'll try some pb blaster. I hate to buy the tool just to remove 2 wiper arms, they're not going back on, I may have a battery post puller that looks like it might help. I'll look again for the tang.

All right guys what's the secret to removing the windshield wiper arms. this is on a 64 dart. I removed the nut on the end but the arms won't budge. Sprayed a little wd-40 and tried prying upward with a 3/8" open end wrench but no luck. Am I missing something or do I just cut them off? Help...

Thanks for the pic and info I'll have to check dimension on my pan but it sure looks like some mods are in order.. I also have a couple of stock pans I'll have to look at. I know one is a 68 340 the other may be a 273 pan I'll check tonite.

So I'm getting from this that my 340/w this pan won't fit without some mods. yes some dimensions please. oh yea this is going in a 64 Dart

I'll be in town that weekend visiting Family and I just picked up a 64 Dart Slant that I'm putting a 340 in. So I'll be looking for parts! Headlite rings v-8 gas pedal linkage,Ect.