Search results for query: *

Yep, has a screw. You can pm me if you want. It would be Tuesday or Wednesday before I could box it up. Your inbox is full.

If you have not found these, I have some from 68. The driver's side short a pillar piece is on the car. I took passenger side a pillar off and can't find it (easily).

I do have an extra if you still need.

I'll check to see if I have one.

PM sent

I have one from a 68 dart. Not a hipo engine. Turns over freely. I consider it a core. I am near Gatlinburg, Pigeon Forge exit of I40.

I should have one from a 68 dart. If there is any difference from 69 I am not aware of it. Is date code important to you?

I have this one from a 68 2dr. hardtop. Obviously not black. Nicely covered but ugly.

I have a 3443977 radiator but I believe that is a 71 year number. It's also for automatic. I'm assuming it needs recored. Bought it for a project but project has been sold.

Need this baffle that inserts into tail light housing. Looks like it's one year only. I am missing one.

I'll probably just cut the door card (it's no use to me) and see how they did it. I expected a push nut but no. Should have taken photo of back side.

I have the pair of these. Still attached to door panels. Looks like they spun the rivets (posts) to attach them. I am not sure how to remove them from the panel and save the posts. Any ideas?

I might have one from a 68 GT also. There are some 69 GTS door emblems on eBay. New reproductions. Not cheap at $199 pair. I bought a pair and they are very nice. FWIW, I tried to save seat emblems from 68 GT and they virtually disintegrated due to heat I suppose.

I have one from 68 dart 273. Located in Jefferson City,TN. I don't know condition but it is complete. Has the single terminal switch. Possibility I will travel to Ky in near future. PM me if interested. Price is around $200

If you have bumpers you might check with Tri City Plating in Elizabethton, TN. Cost is about the same as new from AMD. If you don't have any core bumpers, I have some. Almost any bumper that has not been rechromed will need it. They look ok from 10 ft. but eventually you will want them to look...

My bad. Found this. Probably not what you want.

I am parting this car out. I see nothing wrong with drivers fender. I am not going to Moparty but a friend of mine plans to.

I have an 8 1/4 from a duster. It is 2.45 open. $150. If you are interested, I'll send you some photos. Looks like I am about 200 miles from you.

I have a 65 b body 8 3/4. New brakes, new paint, and pads moved to 43 in center to center. Should work well in a duster. No center section $600. Also have a duster 8 1/4 , 2.45 open for 150$

I have an 8 1/4 from a duster. Shipping would be a killer from TN to CA. I have used Uship before and if someone is headed that way, they may take it along at a reasonable cost.

I have one of those without the heat riser. Have one with heat riser also. PM me and I'll send a photo. Preferably to your cell phone. located in Jefferson City , TN

Looking for complete KH front disc setup. Willing to buy or trade. I have BBP setup (upper control arms included), missing one caliper, to trade if U R interested. Thanks for looking

From my limited experience, the 3 groove crank pulley is for an AC equipped car, a single or double groove crank pulley requires a different water pump pulley than AC 3 groove. Offset and diameter are different.

PM me with your phone # and I'll send you a photo. Door is complete with glass, interior panel and I think it has remote mirror. I found I have two 67 passenger doors, one good and the other with the rust hole.

I have a pair of 67 gt hardtop doors. Drivers side is great condition. Passenger side needs rust hole repaired (likely a clogged drain). Is a convertible door different? I don't know. Located in Dandridge, TN. Maybe one will show up closer to you.

are doors different from hardtop and convertible?

Thanks, fixed that. I will get a photo later today.

If you want to pm me with your phone number I will send you a photo. I can wait until you are ready.

I have one, don't know the year. It is geared in the clouds (like 2.43 or 2.76) but if you have sure grip and gears, then that doesn't matter. Complete with brakes. I think $200 would be fair price. Located in Dandridge,Tn. It would definitely need axle seals as its been sitting a while.

I have a federal pump, pulley, and bracket from a 73 318. If I recall correctly, pulley is around 7 in. diameter and press on. The cap seems to be another hard to find item.