Search results for query: *

Here are mine, they are aluminum though. Give Michael a call. Any interest in custom all aluminum Chrysler steel wheels?

It fits between the relocation boxes nicely. I still need to drill holes in the boxes for the endlinks. Not sure how creative I need to get with the end links. But modification will be minimal if any.

Hellwig 6908 ebody.

No. Car's tucked in the back corner of the garage. Still a lot of build to go. Hopefully in the next couple of months it'll be more Mobile.

I'm running: 18x9 35mm 6.38BS 275/35-18 Toyo 18x11 0mm 6BS 335/30-18 Toyo

Fronts 18x9 6.38"BS +35mm 275 tire Rears 18x11 6"BS 0mm 335 tire

Sure sounds what? Also, here is the next post after the one you quoted.

Had a friend make em for me. Any interest in custom all aluminum Chrysler steel wheels?

Any interest in custom all aluminum Chrysler steel wheels?

They are circle racing wheels. Made for a 11" Ford Chevy cap. When I priced them out they were about 800+ a piece. I wanted a Chrysler wheel that I could have a poverty cap on if I wanted. I have a freind in the wheel business. So I had some one offs made.

Mine

My rear 18x11 aluminum wheel is 29 lbs Stock 15x5.5" is 21.0 lb 15x7" is 24.2 lb 18x7.5 police charger steel 30.8 lbs.

Yep, didn't realize my title was that confusing. These are all aluminum wheels. Forged aluminum centers interference fit into aluminum wheel hoops and welded.

These were patterned off of a stock wheel that I gave to Mike. If you are interested in having a set made please contact Mike. I've had some questions on weight. I'll post some numbers this weekend.

Couple more

I posted this on moparts and in my build thread here. When does money outweigh sentimental value? 1968 notchback build thread Thought I'd post where more could see, in the actual wheel forum. I've have gotten some interest on this set of 18" wheels I had a friend make. So I thought I would pass...

Any chance your strut rods are adjustable or the stock ones are wore out?

When I was in the bodywork stage I had the fender lips trimmed to 3/16" and the front fender pied to make sure I had room for a 26" turning radius. I think that's what you mean. They are not flared or pushed out or baseball bat rolled. Also, barracuda fenders don't have any flare to them at the...

You haven't accomplished anything after bolting on these parts. You don't have your ride height set with you car on the ground, so you can't have camber, caster and toe set... If I set my car on jack stands, account for a small rake, measure where I want my spindles in relation to my fenders...

Suspension work is done except torsion bars are out. Lower ball joints are squared up. If I set my spindles to ride height I'm -2* camber and 3.5* caster. Tire turns fine and doesn't hit at ride height. But under full compression it hits front and rear on the fender lip with a 3/8" bump stop...

That pic shows a little low. I set appx alignment at appx ride height. I forgot to take a pic until I started to let it down, then snapped it. At ride height I'm about 1/2" inside the lip. I'm running 1.14 bars.

Yes I'm trying to run 6.5 - 7.125 of BS on a 9.5. the pic abofe is 18x9 with 6.4 and hits when fully compressed. -2* "You look a little too far down on compression" I'm not sure I understand this comment?

Bump stops are 3/8" poly low profile. Steering stops are on the proforged lowers.

Not sure how you guys are running tires this tall or wide.

Here's another set up. 17x4.5 wheel, 26/6_17 tire, hub to outer wheel lip is 3.75". Hits in the same places at full compression.

Well here's some more info and pics. Appx ride height, ~2* camber, ~3.5* caster. Wheel tool set up at 18x9, 10" overall width, ~6.3-6.4 BS, 3.5" from hub to outer wheel lip, 275/35-18 25.6" diameter. Hits at full compression turning in both directions.

I feel there is a ton of conflicting info on this subject. I read everyone's comments that a 275 on a 9.5 wide wheel will fit no problem but it always turns up they have a 18x8 or 9 with 5-6" BS with a 245 or 255. On a normal 18" hoop will the tierod actually fit inside of the hoop and allow...

13.5 section width for the 335. Will the tire be narrowed at all by the rim?

So I just bought 335/30-18 Toyo r888r's and they're not looking like they will fit, at all. Has anyone actual had success mounting 335 in a minitubed barracuda? Does anyone have any pics of this? Lmk I may return for 315/30-18 Keith

I have this spring kit and will be installing it soon. How did you measure for the frame rail cuts? I'm curious. Thanks, Keith