Search results for query: *

I’m interested in your 741 case,if you don’t plan on using it!

Actually, no I'm not certain that convertibles had one, I ordered it mainly because It was inexpensive & the ad read 63-65 Dart & Valiant w/ no mention to vert or sedan. I still plan on using it (now on the inside of the trunk & trim it to fit. I want the added insulation and the clean look in...

Can't quite figure out how this goes in place? I have seen photos of 69's where it hangs on to the seat hook's! But there are no such hooks on my 64 Vert! I do know now that at least it attaches from inside the well liner! Pic's are worth a bunch of word's! Thanks FABO

UPDATE to this thread! I found 2 very similar clips that may just work with a little trimming! They measure very close!

Anybody!!!

Did you ever find a solution to this! Mine aree toast!! Thanks, I'm going to a huge car show this weekend and don't even know what they look like cause mine are so bad!! Thanks

I agree thanks for reposting, about to take that on myself!

So what does Elvis, his movie Clambake (1967, United Artist's) and a 1966 Dodge Dart have in common? I was watching the end of the movie,(Late nite), Elvis is stopped at a red light in a custom Corvette kissing Shelly Fabares, as a my eye catches a 66 Dart cruising by! The beauty of DVR took a...

My 64 Dart convertible this shot shows the anchors that are on each side bolted thru the floor near the wheel well!

Greg, what is the rear tire size & offset? Any mod needed to the inter fender? I will have a similar combo when I'm done! Good info! I swaped out an 83/4 with aftermarket big bolt pattern axles!

Jos, when do you want to come visit, I've been putting off the wires for weeks!

You wanta come over to the beach when mine arrive and give me a hand?

That is what I was afraid of, I didn't order it, guess I'll keep looking, thanks!

Nice work, I too would be interested in a set of panels and a glove box when your all set!

I was about to purchase, MOPAR DODGE 273 318 340 360 MECHANICAL CHROME FUEL PUMP HP 1005-C And read This: If your engine now has an oem stock fuel pump on it, and it is very close to the frame rail, be sure you have clearance before purchasing this pump. The Extreme series fuel pump is...

Gotter Done! Thank you everyone, it just took a little wiggling to get everything in place! Anyone have torque specs / reference to everything back there?

Just finished a 70's A body, 8 3/4 with new BBP axles, poly bushing etc, and about to bolt into my 64 Dart Convertible, but it doesn't appear to be lining up to the stock holes in the frame! Did I puts the cart before the horse?? Do I need to move the spring perches! Or should it bolt right up...

This is what I'm doing with my 64 Dart Vert, the old top from a 69 I believe was roached so It was covered in a Black Crackle vinyl, then I pained the sides with Crinkle paint. I'm planning on gutting the ash tray under its door and fitting in a cup holder. They make replacement chrome parts for...

All tucked in, just need some trim work before welding!

Any chance the 67 & ups will work?

Looking to upgrade with new bushings while relocating the springs inward, but can't seem to locate a part source for new front bushings for a 64 Dart, Any help!

Mine arrived last week also! I was scratchin my head about the front, so nice too see what you have done! The backs took very little fitting, Pic's to follow!

Marty, found these! www.autobodyspecialt.com - 196266DODGEPLYMOUTHABODYCOMPLETEFLOORPANKIT4PIECES

Yea, that was a way before photo, a few holes there but not terrible, the front pans are Fred Flinstone, and the back feet area had already been replaced, aka pop rivet.

Dan, this is the new master, Mopar Disc Brake Swap Master Cylinder Bolt-On Plymouth Dodge A/B/E Cuda Dart I have 73 spindles etc, no booster, drums in the rear 8 3/4

More of the same I'm afraid under the carpet in the front!

I am restoring a 64 dart Convertible, Resto-mod , turns out there isn't much left of the floor pans! Doesn't appear that there is a source for replacement's. I am considering AMD pans for a 67-up or just getting sheet metal and fabing them in! The front seats are not 64's so there positioning...

Thanks, after a lot of persuasion , I was able to get it loose from the old MC, & yes I am using the new setup! I didn't want to spring for a new adjustable pushrod is there a source for replacement originals?

Switching to front disc's , upon removing the original 64 master cylinder Ive attempted to remove the old pushrod, but haven't had any luck! Is there a trick?

NodakDuster, winter is all most over any luck on the lens! were all on pins & needles??