Search results for query: *

  1. V

    Lokar Kickdown adjustment

    I’ve found shift quality is best adjusted a bit loose on the carb side, otherwise it shifts hard.
  3. V

    How do I find an 8 3/4 rear in the jy

    Look at the end of the axle hub n the center of the wheel. If it’s flush it’s either a 7.25 or 8.25. If it’s dished in it’s an 8.75. You don’t even have to lay down. Pop of the in cap and there it is. This is what you are looking for.
  4. V

    2.76 open to 3.55 Sure Grip...expectations too high?

    It's all got to work together. A stock 318 2bbl won't feel drastically faster going from a 2.76 to a 3.55, but if you took a stock 340 car and went from 3.55 to 2.76s it would seem way more drastic! In my '77 D100 with a warmed over 318, I went from a 3.23SG to a 3.91SG. I noticed right away...
  5. V

    Deep 727 Pan

    It's pretty beefy! I've got it under my truck, so there's clearance, might be too low on a Abody street car.
  6. V

    Deep 727 Pan

    I bought the B&M pan kit! Came with everything it needs! Well built piece!
  8. V

    Pick my converter?

    What do you think about this one? Hughes Performance Street Master Torque Converters 24-25
  9. V

    Pick my converter?

    '77 D100 Curb weight: 3800lbs Gear Ratio: 3.23fd Tire size: 275/60R15 Engine size: LA 318 Compression ratio: 9:1 Cam: Mopar P4452761 (cam specs: Mopar Performance Purple Camshaft Kits P4452761AE) Trans: A727 This is gonna be a street truck. Daily driver, mostly. Regular truck duties with...
  10. V

    Who's in the "I broke a 7.25" club?

    I grenaded one behind a mild 318. It only took two good burnouts and it came apart. It had chewed up everything to the point it was like gravel on the inside.
  11. V

    Can clutch fork be installed w/o removing trans?

    I did it on my dart. Dropped the inspection cover and slid the fork in. Easy work!
  12. V

    Help! Driveshaft length?!

    If it's the same wheelbase, same '75 Abody 8.25" rearend and a '76 Abody 4spd transmission. What would make the driveshaft a different length?!
  14. V

    Help! Driveshaft length?!

    Thanks for the link. That would be more helpful if I had a driveshaft to measure. And no I can't just measure the distance between the rear and the trans because the trans isn't in the car yet. Anybody out there able to tell me what the length of a driveshaft out of a '73-'76 Dart Custom or...
  15. V

    Help! Driveshaft length?!

    So I'm needing a driveshaft for my '64 Dart, which I recently swapped to an Abody 8.25" rear and a 4spd overdrive. My thinking is that, since my dart is a 111" wheel base, and a '73-'76 Dart is a 111" wheel base, that a drive shaft out of any '73-'76 Dart/Swinger should be the right length...
  16. V

    Which driveshaft?!

    No automatic here. I'm pulling the A903 manual, non synchro 3spd trans in favor of a 4spd.
  17. V

    Which driveshaft?!

    So I'm in the middle of some upgrades on my '64 Dart, and need some help. So far I've replaced the stock 7.25" rear with a fresh rebuilt Abody 8.25". Next, I'm about to pull the stock 3spd gearbox for an A/F body A833 overdrive unit. My question is, what stock driveshaft do I need to fit with...
  18. V

    3.23 vs. 3.55

    "Break in", or "Breaking"?!
  20. V

    Factory High Stall converter

    The Lil Red Express trucks came with a 2500 rpm stall from the factory and 3.55 gears.
  21. V

    slant 6 bell housings

    I'd love to find an early 4spd slant bell. The iron ones, not the aluminum over drive unit.
Back
Top