Search results for query: *

Part number 9377-2. This gas carb has been sitting unused since around 2008. I had two of these and had one converted over to alcohol so I really don’t need this one. It’s super clean but will need gone through and given a bath and new gaskets. Asked 550.00 plus shipping from Pa. 16229.

I have a set of Speedmaster heads with 2.02 Speedmaster intake valves that I’m almost finished with and will be on the flowbench Lord willing this week. (Possibly tomorrow) they will flow in the 285-291cfm area and will have a 4-5 angle valve job. I bought these heads bare so for now no valve...

I have a 1971 (440) block that was damaged by a high lift when pulled. It ripped the engine mount off do it would need ground flat, a plate welded over, then mounted with an engine plate. Will not ship and must be picked up in Freeport, Pa. 16229 125.00

Another gas carb I used years ago and in need of a rebuild. I just Dont have the time to do it. I lost all my pictures but if there is any interest I will post them up tomorrow. 375.00 plus shipping from Pa. 16229. Once again it’s a 1050 gas Dominator.

I had a pair of these 1150 Holley gas carbs and I sent one to APD to have it converted to an alcohol carb. No sense in this one sitting on a shelf where it’s been since around 2008 when I bought the pair from a friend. This would need a basic rebuild like anything that has been sitting so long...

Listing for a friend. Brand new set of pressure tested unmolested W5 heads. Message me and I will hook you up with his number. Located in the Delmont Pa area. 3000.00 plus shipping.

Headers were built for a chassis car and come with adapter plates. T&D rockers are old but have been on a friends shelf for spares than my shelf for probably 15 years. Rockers have some dings typical of ball ball pushrods. These are paired rockers and come with mounting bars. Will not ship...

I have a complete set minus one lifter. Dont ask me how but I used one to degree in a cam and test fit a few things and I didn’t put it back. So the one lifter is here and included but to make a complete set I would buy a pair to get the tie-bar. These lifter have 10-15 passes (12 in almost...

I bought these back around 2008 as spares and they have been sitting unused ever since. They are 1.7 ratio individual shaft (one intake one exhaust rocker). They are used and have a few bumps an bruises common on ball ball pushrod rockers. Mounting bars are included but I don’t have the studs...

Turbo spine 9 inch powerglide just freshened by Transmission Specialties. It stalled at 4900 rpm behind my 422 small block Mopar. Zero runs since freshened. 650.00 plus shipping from 16229, Pa (2) at least stock 1.76 powerglide low gearsets. Probably cost to much to ship so pickup at 16229...

Two bare powerglide case. One with the bell cut off for Ultrabell use and one modified (cut out) so a Mopar starter would fit and then modified for strength. 80.00 each and will not ship. Keystone Raceway Park pickup available. Also selling a new set of .055 over 440 Mopar pistons for a stroker...

I’m selling a brand new set of Chevy sized rods that would be good in any small block Mopar stroker engine using Chevy sized rods (6.125 length) ( .924 piston pin). 600.00 plus shipping Holley gas Dominator carb (1150) list number 9377-2. This has been sitting on my shelf for years so...

I’m selling a ported small block Mopar that has been gasket matched to a Edelbrock 7276 intake manifold gasket. The intake showed some nice gains on my flowbench when bolted to a ported Speedmaster head. Now the bad news. I made a hole leading from the entrance of one port to the other. It does...

Mopar Mega block and 440source assembly. Freshly honed by Nick Wilson from Ohio before he passed away. Block is .030 over 440 size (4.350) and in excellent condition Factory deck height for a 440 is 10.725 and this is stamped 10.710 on the deck. The 440source assembly is brand new and balanced...

I have a very nice, very clean 1150 Holley carb I’m listing. It’s one I really didn’t want to sell but I’m finally unloading some parts I’m not using. Probably should have new Boen and metering block gaskets but they she’s ready for some new bests. 550.00 plus shipping from Freeport, Pa. 16229

Selling my used set of 1.6 ratio 360-1 Indy rockers off my 422 engine. These were used on my engine with a .650 lift solid cam and never shifted over 7000 rpm. Asking 275.00 for rockers and shafts or 325.00 for rockers, shafts, hold-downs, and spacers. Plus shipping from Pa.

I have a small block mopar to powerglide Ultrabell (part number 92455) I'm listing for sale. The cert tag is dated April 2016. I switch everything over to ATI cases so I can easily switch over from big to small block. New price is 473.00 and I asking 275.00 plus shipping. located 45 minutes from...

My son is switching his car over to a powerglide transmission so I'm putting these up for sale. Selling my CRT small block 727 that came with my black duster when I bought it. It's freshly rebuilt with zero runs, 5 Raybestos billet drum, reverse manual valve body with transbrake. 1600.00 Sorry...

Ultrabell part number 92450 that sells for 332.00 new at Jegs. Purchased in 2009. This bell housing bolt on to a Chevy powerglide pump after the stock bell housing is cut off. I am including a TCI mid plate that bolts on the back of a big block and converts it to the powerglide bolt pattern. The...

partial set 6 used pistons for sale. PN 142070 506817 I found these listed on Summits website 6 months ago when I was planning future projects. They are stock stroke .040 over 360 pistons. One is pretty banged up and another has some small dings but usable. I cleaned on up and these would make...

I had this rebuilt years ago and it kept everything I owned nice and cool. A couple fins need combed but it’s in very nice shape. No shipping local pick up only in pa 35 miles NE of Pittsburgh 16229. 175.00 FIRM and I mean FIRM.

radiator out of my 1972 Duster that was rebuilt years ago and works great. A few of the fins need a radiator comb. Will not ship and must be picked up at Freeport pa. 16229. 35 miles NE of Pittsburgh pa. 225.00

What I have here is 7 YES 7 (51026) used pistons in what I call very nice shape. Sure there are a few side scratches that are on ALL used stroker pistons but with a quick clean-up could be going in the engine. I would usually order one piston from a Diamond dealer and have but right now I have...

Listing these for my transmission builder ATI Treemaster 8 inch 904 (4600) stall behind a 360 engine Just freshened up and he sold his Duster. Located 30 miles from Pittsburgh, PA. 600.00 plus shipping. Please message me for his phone number. 904 aluminum direct drum used but good condition...

I have a set or two of lightly used Edelbrock small block Mopar valve springs. At least one set will come with retainers and keepers. 60.00 with retainers 50.00 without plus 15.00 shipping to 48 states.

very nice used list number 80528 2 Holley carb for sale (750 HP 4150) I rebuilt this carb 6 years ago and boxed it when I switched to alcohol. I ran 9.80’s in my 2800 pound Duster with a pump gas 408 combo. I never wanted to sell it till I was positive I wasn’t going back to gas. I just took it...

selling the stainless valves out of my old Econo W2 heads. Exhaust valve are 11/32 stem 2.02 valves and 4.990 in length. I have 8 and one extra that is slightly different on the bottom. The intake valve are 3/8 stem 2.02 valves. I have 7 that measure 4.975 and one new one that measures 4.990...

guys I had this radiator recored many many years ago back when I was street racing.(1972-340 Duster) I used it in a couple of cars since and it never failed to keep my cars cool. It is in very good condition only needing some fins straightened. Part number 3574636. This is a steal at the price...

listing this for a Friend. 408 Magnum engine, H beam rods, 11.2 flat top pistons, 550 lift cam, larger injectors, can hear run. 3250.00 and is located in Pa. he is willing to deliver to nearby states. Please message me for his number

Listing a 48 degree 9.200 R block that has a 4.100 bore. Also included is a 3.79 Calias crank, Arrow Rods, used roller cam and lifters, damper, and timing cover. This was used in a dirt track car and I bought it from a Friend so I don't know a lot about it. He had Arrington W7 heads on it but I...