Search results for query: *

My 1st issue... Constantly having to adjust my clutch pedal. What's causing it to keep going low..?? It prevents me from getting into 1st and causes a grind in second.. I hold clutch as far as I can and car will keep rolling or stumble like it's going to stall ... 2nd issue Grind in...

I'm using a Lakewood scatter shield and the opening where bearing retainer goes is a bit larger than the bearing retainer how do I solve this problem c94796 is numbers on bearing retainer

hey guys was wondering exactly how the T/O bearing goes on to the clutch fork I have taken 2 pics Or I had it like the second one before and when I pulled trans one of the springs on t/o bearing was off Wondering maybe my fork is too short??

Hey guys I'm having abit of a problem and not sure how to fix it. My 4 speed does this thing that when I romp on the throttle and go from 2nd to 3rd gear the shifter will lock up in second and won't move it's jamming up and I don't know why . When I drive nice and easy it's ok but say if I...

Is there a way to shorten the throw on an a833?? Seems like the throws on these trannies is so long, I know it's the old skool feel and love banging through the gears but the throw is a bit long I have a pretty standard length shifter is there a way to fix this. Thanks guys

anyone know where can i get one i cant find one the one i have , the prongs are broken

I'm using the center force dual friction clutch and was reading in Mopar muscle that when using a diaphragm style clutch there is no need for the large spring on the clutch pedal assembly. My question is , is the centeforce df a diaphragm style clutch ? Also what is the difference between...

What's the drive shaft length for 4speed to 8.75 rear end . My last driveshaft was 727 to 8.75 Can I use this shaft or do I need a longer one? What's the length from yoke to yoke??

Wat size bolt do I use for the pressure plate also how long should they be. Also torque spec thanks

when using the lakewood scatter shield in my 74 duster with a small block, i can use the A body 12 1/2 inch clutch fork correct?

Wat are the best gears to run with a 4speed?? I have 323s now? Wat are u guys running,want it to get up quick but also don't want it at 4500 when cruising

so i made the rookie mistake of lacing a battery on top of my flywheel while i was cleaning my garage up a bit and the battery leaked acid on the flywheel. its only on the surface it was eatin into, but is it ok to run. will the clutch just burn it off?? thanks

How exactly do the spring washers go on?? Also do the bearings that go on the ball studs get any type of librication or do they go on dry? Thanks I'm getting closer to the 4spd being done just need my fork and rod to arrive and buy a clutch and it'll be done.

i have an aluminum bellhousing . but im more than positive thats not a good idea as i know a scattershield is necessary. 410 stroker with close to 500hp. now im stuck on wat to do ? i put a bunch of money into my motor and trans and dont want anything going to hell after i rev the motor up a...

where can i order one from?? for some reason i cant find one??? i want a site where i can buy since i dnt have paypal for like ebay \, or to buy from anyone from here. any ideas??

got my tranny back from the shop on tues. and now i need a few other things to get it in the car but hooked up my linkage and wanted to know if this looks right?? it seems to shift pretty good .

I have an abody 4speed, with an 83/4 rear. .now it previously had a 727 in it with dame rear. . .soo what drive shaft can be used??? I have the large out put in the 4 speed so can I put that to a 904 shaft. And have the correct length?? Can get one from a 68 cuda that had 904 and 83/4 but want...

Which side is the engine side of the flywheel??

so i was thinking about this for some amount time. i'm not to familiar with the 4speed yet and was wondering wat would be better to use for my 410 stroker??? pilot bushing or bearing, i believe i told my machinist to install a pilot bushing? wats the difference?? and wat is better to use probly...

anyone buy parts from here????. .i was going to order my flywheel from here. good idea? bad idea?? if so where should i order from??

HOW do I go about choosing a flywheel? my machinst needs the flywheel ill be running so he can balance everything. , my 4 speed isnt rebuilt yet and, dont have all the parts, z bar, clutch so on and so on, so how do i go about choosing a flywheel??? also im running the scat 9000 series crank, to...

I was told that when switching from auto to stick, your crank needs to be drilled a certain way for the a833 to work is this true if so does anyone have a pic of the difference???? I also heard since I have a 68 383. Its actually drilled both for auto and manual is this also true?? Thanks

so i just picked up a four speed and now i know its time to rebuild it, it came out of a 71 340 demon, came with a alum. bell housing WHICH IS FOr Sale, pressure plate ,crossmember hurst straight stick shifter and the rods, Now Where do i begin???? i know i need a z bar and bearings...

so i have an opportunity to buy a few different 4 speeds. two of which i am positive they are for "a" body . .thing is that they are pretty far to pick up , and there is another one im not so sure about. its local which is good and he is asking fair price. .but. he's not sure of what body its...