Search results for query: *

Looking for intake manifold for 2000 5.9 magnum to swap to carb. Please post pic and price shipped to 24171 va. Thanks. Needed asap

Anyone have a roller pilot bearing that they could send me. I'll pay thru paypal, as I need it ASAP and cannot wait for brewers, or I'll order you a brand new one to replace it. Putting a 4 speed behind a 360. Thanks

Looking for the outer z bar ball stud and the reinforcement plate that gets welded to driver side frame. Neede a sap. Shipped to 24171 va. Let me know price and paypal info as a time crunch is on my hands. Thanks guys

i am in need of a good steel 340 crank.. i do not care if it is cut but it has to be ready to install. i do not have cash but i do have some parts. so let me know what you may need. thanks guys.

looking to buy a spin stand for my next build, to do it 100 percent. need one asap. does not matter if it is a store bought or homeade let me know what you got

looking for the next resto project. either a 70-72 duster 340 or 71 or 72 demon 340. condition not a factor. let em knwo what you got. looking to spend 6k tops

i need the hood latch and emergency catch lever off a 70-72 duster or demon. price shipped to 24171 va. thanks

any one got a set they will sell? please post pics and price shipped to 24171 va. thanks alot

i am looking for a torsion bar adjusting bolt for passenger side. also need the little piece that the bolt threads into. need one asap. just let me know price shipped to 24171 va thanks

i need the two bolts that mount to trunk pan and hold the gas tank straps. price shipped to 24171 va. and they need to be usable. do not need another set with the nuts seized to the bolts!. thanks

i am in need of a good/uncut under the hood harness for my 70 duster. looking for one that has electronic ignition if possible, and needed asap! let me know what you got and price shipped to 24171 va

guy, i am desperate for clutch pressure plate bolts and 4 speed flywheel bolts asap please let me know!

hey guys, anyone got a line on a rust free passenger side fender? the nicer the better, but do not want to pay nos prices! thanks needed for a 70-71 duster/scamp

any one have one of these pieces that they would sell me? need it shipped to 24171 va. needed asap thanks this is the piece that screws onto the end of the shift rods, and aloows adjustment

i am looking for a duster hood that needs no work to the under side. it can have a ding or so, but no big damage. CANNOT HAVE ANY SURFACE RUST OR PAINT PEELING ON THE UNDER SIDE! id even take one that is setup for dual hood scoops for pinky! LET ME KNOW WHAT YOU GOT. THANKS

i need all the bolts and washers for mounting my h.p manifolds to the heads. need to be in good usable condition with no stripped threads. price shipped to 24171 va. thanks

looking for a set of painted sport mirros. paint probles is ok. just need thenm to redo as i prep pinky for paint. let me know what you got, and how much. thanks

looking for the three rods for an a body. also need the tabs that are bolted to trans, that rods are attached to with a clip let em know how much, or i have tons of parts to trade.

just like title states. i need a thumwheel radio for a rally dash. does not have to work. just need to fill the gap, with the factory look!. please give me a price shipped to virginia. needed asap. also need the 3 non a/c heater cables. must be in usable condition

i am looking for a passenger side h.p manifold with a a late 69 to early 70 date code. however, ill take any one of the early good h.p mani if you have one. thanks

looking for driver quality front and rear seats out of a 70 duster. needs to be a bench seat. let me know thanks

ok, i need front windsheild trim. must be nice. all rear windsheild trim. i have bottom piece, but will take all need a 70 frnt bench seat in black, that is in good driver quality or better black interior front pillar plastics, black door panels in good to ecelent shape. need a...

LOOKING FOR........................... front fenders with no dents or extreme rust 70 front bench seat in black. nice driver quality rear quarter patches for around the wheel well lowers LATE 69-EARLY 70 340. MORE COMPLETE, THE BETTER FULL 4 SPEED SETUP ANY AND ALL LINKAGES ,SHIFTER...

anyone got a junk engine sitting around, that they would take all the manifold bolts and the four nuts with washers off for me? how much needed asap. thanks

guys, this is a long shot but figured i would try...... looking for a nice tail panel, trunk floor, quarter trunk floor extensions, both quarters, not a set of junk skins. need the entire thing. also need full rockers.............. shoot, if anyone has a solid roller, let me know

looking for a stock 340. whether it be a 69 or a 73. would like to find one that has a mid to late 70 build date, but does not break the deal. does not have to have intake, carb, heads, but nice to have all the pullies and stuff. let me know what you got.

like the title says. need on that is not a rot bucket, and needs to be bondo free. i know it is a long shot shy of buying a amd new repop but have to try

i need a 150 speedo, wiring harness for a 70 rally dash, and the one circuitboard that does not have the 11 pin connector on it. i need the other side, that has just the plug in for the bulbs i think. needed asap, let me know what you got

lokking for a sharktooth grille. even if it has damage, as long as all the pieces are there and marker light, bezels, i would be intrested. SHOW ME WHAT YOU GOT.LOL

i have a real nice black dashpad. i am wanting a blue one after some thought. anyone have a blue one, that they would trade a nice black one for? pm me. lets talk