Search results for query: *

Anyone here have a source for obtaining just shims for setting up pinion depth ? I would like to get locally, but haven't had any luck only through mail order and I'm no longer comfortable giving info over the net, Tried the various chain stores but no one stocks or can get a shim kit, only the...

Not sure where to post this, either here or the race section, but here it goes. Can a reverse pattern manual valvebody be used in a stock linkage console equipped car. I know an after market shifter can use either, but considering going with either a reverse pattern or a fwd pattern instead...

Getting some different answers, from chevy guys mostly, but my thoughts are a torque convertor should respond better from an engine that produces more torque. Am I wrong in thinking this ?

Has anyone on here ever welded balance weights on a neutral balance convertor to use it on an ext. bal. motor. I have a good neutral bal. I would like to use on an ext. bal. motor. I haven't had any luck on a used B&M flexplate and found weights for half the price. I have a 220 amp mig welder to...

Picked up a 727 and never went through one, so my questions who here has done one and any special tools needed or if so anything that can be used in place of the special tools. Been a mechanic for several years but never got into trans rebuilds, any help, experiences would be great. Sorry if...

I have a 1975 dart 360 and would like to use my neutral balance convertor with this ext balance 360. Friend of mine has a flexplate, I haven't seen it but he had it behind a ext bal 340 or 360 he is not sure, been several years. The number on it is 10234. I can't seem to locate this number...

Made some passes on a rebuilt 742 case and used the Valvoline 80/90 gear oil that states that it has the limited slip additive in it. I made 6 passes and noticed last weekend that I'm getting clutch chatter when backing up and pulling forward in slight turns. The diff was set up by a local known...

Haven't had the chance to get to the track yet. I wondered if someone could give me an idea if the would be much change in in RPM'S from going from a 39' to a 3.55 gears. I have two tire choices that I will use. One being a street tire and another a Hoosier quick time tire. Check the diameter...

I picked up a 742 case sure grip and wanted to use but I found out that it's missing the buttons or pins that keeps the axles from moving in and out or in adjustment. Can these buttons be put in the suregrip without taking the sure grip apart. Not familiar with the sure grip. any help would be...

Putting a B Body rear into an A body and the factory perches have already been removed when I got it. So my question is, to get the proper measurement for the perches, can I use the inside flange of the housing to place the new perches ? I had thought of removing the 8/14 rear and placing the...

I got a lead on 2 different 8/34's One is a 742 case and the other is a 489. Which or is both re buildable and which would be a better diff ? Cost wise, rebuilding if need be which would be the better choice ? Not familiar with the 8/34. Thanks.

I have a 727 and the deep Mopar Perf. pan installed. I had drained the fluid which wasn't in there long and it may have 100 miles on it. I had drained it because I had to replace the selector shaft seal. I put a gallon of new fluid in it and it is just on the dipstick, so I need more fluid I...

I'm sure this question has been asked before and I did some research but unless I overlooked it or didn't find it my apologys. Looking at swapping the 8/14 rear for an 8/34. The 8/34 is from an A body with the smallbolt axles. So my question is when I go to aftermarket axles with the 4.5 bolt...

Need opinions. I have a dart sport with a stock 360 with an 8/14 rear with 3.21 gears that has bearing noise, not sure if it's carrier or axle yet. So thinking next year may be doing some racing in street class once in a while, with either street tires or DOT slicks. My question is do I stay...