Search results for query: *

1994 - 2003 Harmonic Balancer for Dodge 5.9L/360 Damper USMCA | eBay New custom made replica harmonic balancer, damper by: Advanced Automotive Components, Inc.

I've read 5,000-5500. 2001 engine, speedmaster intake, 750 holley, dougs d453's I'm using an old MSD 6al box and currently have a 6000rpm chip. Wondering what chip I need to purchase just to be safe? Thanks

Just read a couple cool articles. On-the-Road Holley Carb Tuning During Power Tour - HOT ROD Magazine Chevy Carburetor Tuning Tips - Chevy High Performance Magazine

360 h116 pistons,scat rods,factory crank,ede heads,air gap,750dp holley, holley carter high flow mechanical pump with holley fuel regulator, msd 6al,accel dist, 727 2800 stall, 8 3/4 (742 3.91 and 3.23) Would like to run the 3.23's all the time and try hitting it with a 100 shot. 97% street...

I was going to use two breathers and a pcv. Knocked it out and quickly found out there isn’t a grommet made that will fit. Brought it to my local engine shop and he knocked it outside of the park. He machined both the top and the bottom so a standard grommet would fit. It's roughly 1/2" deep...

I bought 6 quarts and two of them are different. What changed and should I run it or order two more and hope they match?

I've been battling an oil leak for a long time. Stubborn and cheap as I am put new pistons and rings in with just a monkey ball hone. After multiple oil pan gasket and rear main seal replacements. The conclusion is the rings aren't sealing and its blowing oil out the rear main. I have...

69 dart 360 ede heads,voodoo 60403, speed pro 416 Pistons,scat i beams, ede air gap, 750 Holley dp. 4 speed cf dual friction 2.66 8 3/4 3.91 have a 3.23 set up that I'd like to swap soon. Car runs good. But I recently swapped cams so I thought I should check the cranking compression. It's...

read so many different answers. What's everyone using. Thanks

Went out with some biker friends last night. Needless to say 3.91 gears absolutely sucked. I have a 360 ede heads,rpm air gap, xe284 cam, sp 405cp pistons, stock rods/crank, 273 adj rockers, 727, holley 750 street hp mechanical. I am thinking about putting the 275deh cam back in and the...

Installing new motor mounts. engine sits high (in the hole) on the passenger side and low in the hole on the drivers side. What is the correct way to make sure the engine is mounted correctly. Planned on taking my cherry picker and lifting the drivers side head bolt. Also the transmission...

I was having trouble adjusting the throttle cable on the dart. Either the blades didn't open all the way or they didn't shut all the way. I took the gas pedal assembly out and filed the back side of the stop. took a 1/16 off and it works perfect. Just thought I would spread the word.

Thinking I have the wrong crank pulley but who knows. The water pump belt is supposed to be lined up with the inside crank groove.

My current combo has went 7.88 in the 1/8th. Currently running 4 valve relief speed pros with a comp xe284 cam, ede heads, air gap, 750 holley street hp. midwest converter that stalls at around 3200. 3.91 gears with 26x9.50-15 hoosier qtp. Last year I had a drive line vibration that...

externally balanced 360 street strip 6500 max rpm. Not looking to break the bank. Will a stock napa unit from a 80's pick up do the job?

1085 napa filter. Installed a aftermarket dipstick want to be sure. Looking like 4.5?

Which build would be better and why? Street strip dart. Just picked up a 4 speed. Looking to build a high winding monster. Top end will be same as listed below. Cam is still up in the air.

I have a 69 Dart that I am installing floor pans and patching the crossmember. While the pans were out I thought what better time to install a overdrive trans. I was thinking A518 (non lockup two wire). I found a donor trans from a 1 ton van that I think I could pick up for 100 bucks. I just...

360 405p SP pistons, stock rods, cast crank. 9.5 comp Comp XE284 cam. I was told the cam I am running is a mismatch with the compression ratio. I did a cranking compression test last night and it was 160 on all cylinders (engine warmed up, throttle zip tied open, MAC Tools gauge) 9" of vacuum...

Does anyone know what the adjustment is to reduce total timing on this distributor? I would like to be at 16-18 initial 31-32 total I know MSD distributors have a bushing. I was told the accel unit uses an allen screw adj. Is this true? anyone run this unit?

I have been reading up on wide band o2 sensors for tuning and they are saying that 13.8 is perfect for air fuel mixture. in looking at my dyno sheet it seems to be running super rich. Im wondering what everyone is running for jet sizes. The dyno run was done with 71,s. Everybody I have...

Ok so the problem is I dont have the money to buy the right electric components haha. I have a 1969 Dodge Dart with a 360, 727 2800 stall, 8 3/4 3.91. I just recently had bad luck with a couple carter electric fuel pumps. The electric pump worked great for about a month before it would only put...