Search results for query: *

I have for sale a set of used main caps that came from a 318 engine. They are all in excellent shape and have been cleaned. The bolts that were used on this engine were a mismatched set so I’m just including the correct ones that I found. The oil pump attaching bolts are also included. These...

I have for sale a set of 8 used Silv-O-lite .060 over, cast pistons P/N 1279 that came from a 360 LA engine using the stock 3.58” stroke. Silvolite S1279-060 Silv-O-Lite Cast Pistons | Summit Racing These pistons are clean and come with the matching pins. Each pin was put back with its...

I have for sale what looks to be an MSD extension cable with 4 different color wires in a plastic covering for the 7AL ignition box. Red for switched power, Orange for coil +, Black for coil –, and White for points or original ignition amplifier. One end has the end connectors to go connect...

I have for sale a pair of gently used aftermarket SBP, 8 ¾, A-body axles from Dutchman. These are the stock length 27 11/16” axles, with ½ x 2” screw in studs, OEM adjustable bearings and stock 30 spline ends. These axles were taken out of a 1969 Barracuda so will fit any of the A-body cars with...

SOLD pending receipt of payment. I have for sale a new, never used engine oil filter relocation kit that I believe is a Trans Dapt # 1113 Trans-Dapt Performance Products 1113 Trans-Dapt Performance Remote Oil Filter Relocation Kits | Summit Racing It’s complete with all the fittings and...

I have for sale several lengths of used stainless steel braided fuel line with female AN fittings already attached. Here is the list: 1 -8 line with female AN fittings on both ends. 17” in length end to end 1 -6 line with female AN fittings on both ends. 15 ¾” in length end to end 1 -6 line...

I have for sale a set of 3 clutch cross shaft (Z-bar as most folks call it) nylon pivot bushings. These are the bushings that cup the balls on each end of the round part of the shaft. Unfortunately, I only have three of them. Two are used and the third one looks to be new. I would like to get...

SOLD pending receipt of payment. I have for sale 6 of the cupped SB exhaust manifold washers. They are all in great shape and not all rotted. I would like to get $5.00 for all 6 washers plus the shipping. Ken Edison, NJ

I have for sale a used BB NON-AC single groove water pump pulley that’s in excellent shape, has been cleaned and painted. It measures just under 5 ¾” in overall diameter and 2 ¾” deep. I would like to get $12.00 for it plus the shipping. Ken Edison, NJ

SOLD both sets pending receipt of payment. I have for sale some NON-OEM small block intake bolts and washers and NON-OEM small block engine mount bracket bolts, washers and nuts. They all came off of a badly damaged and unusable 340 engine. Everything is clean with all the threads in excellent...

SOLD pending receipt of payment. I have for sale a set of 4 used OEM 340 windage tray main caps bolts. These are the correct bolts to attach the windage tray to the main caps. They are in perfect shape and have been cleaned so ready to install. I also have some bolts that attach the windage...

I have for sale a set of 8 used Silv-O-lite .060 over, cast pistons P/N 1279 that came from a 360 LA engine using the stock 3.58” stroke. Silvolite S1279-060 Silv-O-Lite Cast Pistons | Summit Racing These pistons are clean and come with the matching pins. Each pin was put back with its...

I have for sale a set of used main caps that came from a 318 engine. They are all in excellent shape and have been cleaned. The bolts that were used on this engine were a mismatched set so I’m just including the correct ones that I found. These caps can be used on any of the 273, 318 or 340...

I’m selling this distributor cap/rotor kit for a friend of mine. He ordered the wrong kit. This kit is a NEW Summit G5223 and fits the Mopar MSD BB and SB Pro Billet distributors along with any of the GM points style distributor applications. The cap has the female design socket ends for the...

I have for sale a used but in excellent shape, carb throttle return spring bracket. It looks to be an OEM 2-bbl 318, 360 application but was taken off of a 360 Holley 4 bbl engine, I believe the only difference is the throttle return spring length. It’s been cleaned and has a coat of primer on...

I have for sale a set of new collector tether cables and clamps that were for a 440 project that was never finished. This kit consists of 2 cables, 2 primary tube clamps and 2 collector clamps. These parts were never installed on any headers and is still in the original packaging. The cable...

I have for sale a really nice OEM 360 cast crank, casting number 3418640. This crank was in a 360 block with a 1971 casting date. This is very clean with the rods and main journals already cut .010/.010. The only thing that this might need is a very light polish. Other than that, it needs...

I have for sale a set of 5 UEM ICON stroker pistons and corresponding pins for either a .020 over 340 or a .060 over 360 LA using a 4.00” stroker crank. They are the flat top design with 2 valve reliefs, are forged aluminum and are the full floating connecting rod design. These pistons are used...

I have for sale a used 58-78 BB NON-AC single groove water pump pulley that’s in excellent shape, has been cleaned and painted. It measures just under 5 ¾” in overall diameter and 2 ¾” deep. I would like to get $15.00 for it plus the shipping. Ken Edison, NJ

I have for sale some SB rocker shaft curved washers/spacers. There are 3 of the wide ones and 4 of the narrow ones. They are all clean and undamaged. I would like to get $6.00 for all the spacers plus the shipping. Ken Edison. NJ

I have for sale a used OEM flexplate that came from a SB engine. It measures 10 ¾” overall with a 10” bolt pattern. This will fit any BB or SB as long as the converter bolt pattern is the 10" pattern. There are absolutely no issues with this flexplate. I am also including the 5/16” converter...

I have for sale a set of 4 small block rod bearings that are .030 under. They are new and still in the original boxes. 3 of them are Federal Mogul P/N 2130CP-30, and the 4th is Sealed Power P/N CB-481-30. Sealed Power CP-Series Rod Bearings 2130CP 30 I would like to get $8 plus shipping for...

I’m selling this distributor cap/rotor kit for a friend of mine. He ordered the wrong kit. This kit is a NEW Summit G5223 and fits the Mopar MSD BB and SB Pro Billet distributors along with any of the GM points style distributor applications. The cap has the female design socket ends for the...

I have for sale a set of used main caps that came from a 1986 318 engine. They are all in excellent shape and have been cleaned. The bolts that were used on this engine were a mismatched set so I’m just including the correct ones that I found. These caps can be used on any of the 273, 318 or 340...

I have for sale a used MSD Pro-Power coil P/N 8201. This coil was in a large lot of parts that I bought. I installed it and it worked perfectly using my MSD ignition tester. MSD Ignition 8201 MSD Pro Power Coils | Summit Racing The picture shows 2 coils but one has been sold. I would like to...

I have for sale a used 58-78 BB NON-AC single groove water pump pulley that’s in excellent shape, has been cleaned and painted. It measures 5 ¾” in overall diameter and 2 ¾” deep. I would like to get $10.00 for it plus the shipping. Ken Edison, NJ

I have for sale a set of 8 used Silv-O-lite .060 over, cast pistons P/N 1279 that came from a 360 LA engine using the stock 3.58” stroke. Silvolite S1279-060 Silv-O-Lite Cast Pistons | Summit Racing These pistons are clean and come with the matching pins. Each pin was put back with its...

have for sale a used right side, E-body, SB engine mount bracket. It’ll fit any of the SB engines. This bracket is straight, clean and painted. It comes with the 3 OEM attaching bolts, nuts but only 2 of the flat washers. I would like to get $6.00 for everything plus the shipping. Ken Edison, NJ

I have for sale a very little used SB Melling M72HV high volume oil pump, pickup and pump attaching bolts. This will fit on any of the SB LA, Magnum and V-6 engines from 1962-2003. These parts were from a large lot of engine parts that I bought. The oil pump was disassembled and found to be in...

I have for sale an OEM car style oil pan that was from a 1971 360 engine. This pan will NOT work with a 273, 318 or 340 engine. It has #438 stamped on the bottom of the sump. Fairly dent free but the inside can use some bead blasting to get the surface rust out. It’s got a primer coat of paint...