[Found!] Early A clutch parts needed

[SGBARRACUDA]

I’m helping a friend and another member rebuild/restore some clutch pedals and parts.
I need a clutch pedal over center spring. A master cylinder push rod. I need a V8 bell crank ( this one is Mickey moused beyond belief) I need the bell crank ball on the bell housing side. I need two sets of the plastic halves that go on the bell crank ball studs. Oh and a brake light switch.

 

[KosmicKuda]

If you get no response, check with Brewer's Performance.

 

[halfafish]

Hey Roy, what's the length on your master cylinder pushrod? I think I have one squirreled away somewhere on Parts Mountain.

 

[SGBARRACUDA]

Hey Roy, what's the length on your MS pushrod? I think I have one squirreled away somewhere on Parts Mountain.

The one that goes thru the firewall?

 

[SGBARRACUDA]

Chris bought these parts from a member on here. Boy did he ever sell a bunch of junk.

 

[halfafish]

The one that goes thru the firewall?

Yes, if that's the one you're looking for. Isn't that it in the first photo, on the right?

And yes, what a bunch of junk. That's some "creative" repair work for sure.

 

[SGBARRACUDA]

I think that rod is usable. I had to straighten this one out. I’ll measure this one tomorrow and get back to you to compare them. Thanks.

 

[SS Lancer]

I think that rod is usable. I had to straighten this one out. I’ll measure this one tomorrow and get back to you to compare them. Thanks.

Thank you Roy

 

[SGBARRACUDA]

Still looking for some parts.

 

[SS Lancer]

Still looking for some parts.

Thanks Roy

 

[oldkimmer]

Hey Roy, I have this stuff. The new stuff was for a 73 cuda. Use pieces idk. Kim

 

[SGBARRACUDA]

Measure the over all length of the brake push rod. I’ll measure this one. I’ll get a hold of 1badcolt , Chris and get him to get in touch on the other stuff Thanks

 

[oldkimmer]

6 1/2 inches

 

[SGBARRACUDA]

6 1/2 inches

I'll check this one tomorrow. Thanks

 

[SS Lancer]

Measure the over all length of the brake push rod. I’ll measure this one. I’ll get a hold of 1badcolt , Chris and get him to get in touch on the other stuff Thanks

Ok , Roy so go ahead and purchase ?

 

[SS Lancer]

Hey Roy, I have this stuff. The new stuff was for a 73 cuda. Use pieces idk. Kim

View attachment 1715666930

View attachment 1715666931

View attachment 1715666932

View attachment 1715666933

View attachment 1715666935

Ok , pm total with Shipping to GA [ 30228 ] zip code thanks chris
I know with covid shipping is slowed down take like 3 weeks to get it here.

 

[SS Lancer]

Measure the over all length of the brake push rod. I’ll measure this one. I’ll get a hold of 1badcolt , Chris and get him to get in touch on the other stuff Thanks

Thanks Roy

 

[SS Lancer]

6 1/2 inches

Old message
If u dont mind I will ship stuff to roy he is rebuilding assembly for me
Thanks Chris

 

[SS Lancer]

I will pay then ask Roy to give you his address so parts can be shipped directly to him thanks Chris

 

[SS Lancer]

Measure the over all length of the brake push rod. I’ll measure this one. I’ll get a hold of 1badcolt , Chris and get him to get in touch on the other stuff Thanks

Roy tell
Kimmer what all I need for u to finish restoration etc # thanks Chris

 

[oldkimmer]

Roy tell
Kimmer what all I need for u to finish restoration etc # thanks Chris

Roy did

 

[SS Lancer]

Ok thank you Sir
Roy will get it all worked out he is restoring pedal assembly
Im not knowledgeable about the assembly in general sorry
Roy said basically the entire assembly was used up poor shape etc.

 

[SGBARRACUDA]

I need one more item. I need the Z bar or bell crank.

 

[SS Lancer]

Measure the over all length of the brake push rod. I’ll measure this one. I’ll get a hold of 1badcolt , Chris and get him to get in touch on the other stuff Thanks

Thanks Roy , just forward whatever I need and I will pay them .

 

[SGBARRACUDA]

Thanks Roy , just forward whatever I need and I will pay them .

Only need the bell crank. I got everything else.