[SOLD] Free Slant Engine n accessory Parts and 10$ BellHousing

[Rice Nuker]

73 slant 6 from an automatic car duster.

Everything or anything off this motor except the clutch fan setup.

Most the stuff has been changed to free plus shipping.
I'm just hoping someone could use this stuff b4 I chuck it off a cliff.

Shipping from Jackson CA area.

Updates, accessories sold, bell housing spoken for.

This motor (has 125k) ran smooth about 6 years ago but sat outside for 3 years like you see it and may be full of water, I don't know. The carb has been taped off but that likely did not prevent a bit of water from entering the engine.

Sold: Carb n choke thermo device.

Sold:Brand New water pump free + shipping dollars.

Sold: Brand New upper rad hose free + shipping dollars.

Sold: Brand New distributor cap and rotor free + shipping dollars.

Sold: Brand New fan - alternator belt free + shipping dollars.

Sold: Factory Distributor free + shipping dollars.

Sold: Manifold hold downs and nuts.

Spoken for: Transmission bell housing 10 dollars firm. I dont know what this goes to. I can measure dimensions with a caliper it if needed.

Alternator free + shipping dollars. Condition unknown although it worked 6 years ago.

Nice condition starter off my 360 Duster, 50 dollars firm.

Any other parts off this thing, is free + shipping unless its some internal crankshaft or something, then it may be 10 or 20 bucks to pull it out.

I am hauling this off to the the recycle in about a week.


Thanks Fabo.

 

[memike]

pm on it's way

 

[waguy]

PM sent

 

[speedog24]

PM sent your way!

 

[Rice Nuker]

Update:

01:07 PM speedog24 = first on carb



12:41 PM memike = first on both pulleys, dist, cap, rotor, fan belt, water pump.


11:59 AM MOPAR4Me = first on bellhousing

 

[Rice Nuker]

Bellhousing still for sale..
MOPAR4Me does not want the bellhousing. He did provide us with specifications which I will post here, very nice MOPAR4Me.

It is for a mild (very low performance I would think) application:

9.5" slant six bellhousing cast #3743643, uses 122 tooth flywheel, to fit 1976-80 Dodge truck and A/F body 225 slant six A-833 overdrive applications, 5.125" bearing retainer opening.

 

[B-NA$TY]

Pm sent

 

[Rice Nuker]

Price dropped on bellhousing. I was firm on price till a member clued me in on its potential. So it is now 10 dollars plus shipping.

It is for a mild (very low performance I would think) application:

9.5" slant six bellhousing cast #3743643, uses 122 tooth flywheel, to fit 1976-80 Dodge truck and A/F body 225 slant six A-833 overdrive applications, 5.125" bearing retainer opening.

 

[yellowdart72]

Price dropped on bellhousing. I was firm on price till a member clued me in on its potential. So it is now 10 dollars plus shipping.

It is for a mild (very low performance I would think) application:

9.5" slant six bellhousing cast #3743643, uses 122 tooth flywheel, to fit 1976-80 Dodge truck and A/F body 225 slant six A-833 overdrive applications, 5.125" bearing retainer opening.

pm sent on bellhousing

 

[memike]

I want to publicly thank Rice Nuker for his patients awaiting my reply today, my day was out side 67 degree's and I had my Grandchildren today and this evening And a big thanks for the time to get these parts out to us /6 folks before he sends them to the scrapper :thumleft::thumleft:
Thank you for all the work you are and have went threw =D>

 

[Rice Nuker]

hey, mopar community has to stay strong. If I have stuff that I ain't using for 10 years, Ill pass it along.

 

[Rice Nuker]

PM replied.

pm sent on bellhousing