[FOR SALE] left over parts, pulleys, brackets, etc.

[diymirage]

all items located in Holland MI, 49424, O.B.O. and free pickup (buyer pays shipping)

(small black LA parts)

double groove water pump pulley, 2 7/8 inch deep
got this in a package deal, it is painted semi gloss black by previous owner
$15.00 plus shipping

single groove water pump pulley, 3 inches deep
sandblasted and painted satin black
$15.00 plus shipping

2 piece/3 groove crank pulley
I removed this from a 75 360 that came from a motor home
not sure what to say about it, it consist of a 2 groove pulley and a single groove pulley placed inside of it
I sandblasted and painted it before I noticed it was a 2 piece set up so could be redone better.
I imagine this can be used a 2 groove pulley BUT the two groove are different diameter.
$25.00 plus shipping (for both parts)

alternator mount for A/C setup
could use a blast and paint
$15.00 plus shipping

electronic distributor with cracked cap
was removed from same 75 360
the motor was said to be running when it was removed but I never got a change to see/hear it run for myself
there is a little up and down play on the shaft, none sideways
$20.00 plus shipping

727 transmission braces
sandblasted and painted flat black
I intended to re-use these but the wont fit with the headers on
$10.00 plus shipping

non roller timing set
comp cams 3203 http://www.summitracing.com/parts/cca-3203
came with my cam set but I installed a double roller instead
brand new in open box
$20.00 plus shipping PAYMENT RECIEVED

2 sets of 3 to 2.5 inch reducers
first set is made by dougs and is 5 inches long
3 bolt flange attached to the reducer
(these seem to be coated)
$20.00 plus shipping

second set is made by flow tech and is 3.25 inches long
3 bolt flange slides over the reducer and clamps down when the bolts are tightened
raw steel it looks like
$15.00 plus shipping

(slant six parts)
ignition coil
car was running and firing fine when removed
$10.00 plus shipping
(bracket and coil wire included at no extra charge)

2 3/8 inch fan spacer
should work on a LA engine aswell
$15.00 plus shipping

7 blade fan
steel blades
$15.00 plus shipping

slip on yoke from a 904 transmission
$20.00 plus shipping

I also have a steering wheel adapter
it does not have the horn set up but will allow you to install a grant steering wheel on an A body (as long as you don't need the horn function)
$10.00 plus shipping

miscellaneous brackets
$5.00 a piece plus shipping
(the red one has an extra hole drilled in it, allowing it to function as a steering wheel puller)


pictures will be up as soon as the wifey puts her phone down for a minute

 

[diymirage]

timing set is SOLD

hurry up people, these parts are going fast

 

[68GTconvert]

Do you still have the 7 blade fan? Have a pic of it?

 

[diymirage]

Do you still have the 7 blade fan? Have a pic of it?

 

[diymirage]

single groove water pump pulley



double groove water pump pulley



triple groove crank pulley



and two pieces pulled apart



alternator mount for A/C equipped small block

 

[diymirage]

electronic distributor with broken cap



small block to 727 braces



dougs reducers



flow tech reducers

 

[diymirage]

/6 225 coil



2 3/8 fan spacer



steering wheel adapter



and miscellaneous brackets
(the alternator bracket is the same one already shown)

 

[moparmat2000]

PM sent on the pulleys, and distributor.

 

[AlV]

PM sent on the Trans Braces

 

[diymirage]

PM sent on the Trans Braces

and paid for, trans braces are SOLD

 

[jomoper]

PM sent RE: Reducers.

Gonna pass ,Thanks won't need them after all.

 

[67notch]

Pm sent for reducers if not sold

 

[diymirage]

shipping quotes send on the Dougs reducers and the steering wheel adapter

 

[diymirage]

dougs reducers paid for and shipped out

 

[68 Notch Back]

PM sent about the crank pulleys

 

[kelleherdl]

PM sent on double groove pulley.

Dennis