[SOLD] Parting out '75 Duster

[71ChargerSE]

Ok folks, parting out this Duster, original slant 6/auto, no motor or trans, 7-1/4 rear.
Right front fender $100 no rust
Left front fender $50 no rust, dented
K frame $50 with lower arms
Doors, complete $50 each
Tail lights, with bezels, light pitting $40/pair
Radiator $50
10" small bolt front drum setup $50

Dash pad is trashed, dash frame cut, deck lid dented where it was pried open.

All other parts make offer

ALL PARTS OR BEST OFFER

ALL PARTS PLUS SHIPPING



View attachment ForumRunner_20130921_101810.jpg



View attachment ForumRunner_20130921_101833.jpg



View attachment ForumRunner_20130921_101854.jpg



View attachment ForumRunner_20130921_101905.jpg



View attachment ForumRunner_20130921_101931.jpg

 

['73red-duster]

P M sent

 

[71ChargerSE]

Replied. Thanks.

 

[Rengo]

Pm sent!

 

[Rengo]

Interior panels
Is the back seat a fold down? I think most were
Head rest

Just listing more things people should consider asking about.

 

[71ChargerSE]

Non fold down seat, interior panels weather beaten, but the head rests looked ok at a glance. I'll check them again when I get home.

 

[71ChargerSE]

Right front fender $100 no rust
Left front fender $50 no rust, dented
Doors, complete $50 each
Tail lights, with bezels, light pitting $30/pair
Radiator $50
10" small bolt front drum setup $50
2 14" small bolt wheels
2 13" small bolt wheels
Maroon A pillar covers and kick panels $40
ALL PARTS OR BEST OFFER

ALL PARTS PLUS SHIPPING

 

[cowest432]

if not broke i'll take them

 

[71ChargerSE]

if not broke i'll take them

If what's not broke?

 

[cowest432]

sail panels sorry

 

[71ChargerSE]

No problem, unfortunately no, they are broken up pretty badly.

 

[gkmopar]

Difficult to see in the picture but is the passenger drip moulding still there? If so I am interested.

 

[mopar madness]

What's the pillar trim look like.
Thanks

 

[71ChargerSE]

The pillar trim is decent, its maroon in color.

 

[71ChargerSE]

Difficult to see in the picture but is the passenger drip moulding still there? If so I am interested.

It was mashed and bent.

 

[MidnightSwinger]

Where in tx? Wiring for Electronic Ignition, and solid state voltage regulator still there?

 

[71ChargerSE]

Fort Worth, I have the engine harness.

 

[bdusted440]

got a pick of the driver door?

 

[MidnightSwinger]

Would you sell just the spindles? Also need to upgrade my 66 to a dual pot master, if you have the parts for that.

 

[71ChargerSE]

Bdusted, doors are sold, sorry.

 

[71ChargerSE]

Right front fender $100 no rust
Left front fender $50 no rust, dented good dog leg section for rust repair.
Tail lights, with bezels, light pitting $30/pair
Radiator $50
2 14" small bolt wheels
2 13" small bolt wheels
Maroon A pillar covers and kick panels $20
ALL PARTS OR BEST OFFER

ALL PARTS PLUS SHIPPING

 

[SRT_DSTRHOLC]

How much for driver side door handle with its linkage that's connected to it?

 

[71ChargerSE]

Doors are sold.

Car is gone.

Right front fender $100 no rust
Left front fender $50 no rust, dented good dog leg section for rust repair.
Tail lights, with bezels, light pitting $30/pair
Radiator $50
2 14" small bolt wheels
2 13" small bolt wheels
Maroon A pillar covers and kick panels $20
ALL PARTS OR BEST OFFER

ALL PARTS PLUS SHIPPING

 

[amoparacer]

do you have the grill.

 

[71ChargerSE]

The grille is broken.