Search results for query: *

Hi Guys ! I have a 68 Dart Gt with the factory 318, automatic transmission and factory a/c. It's been restored now for about 5 years. I have had to put two alternators on this car - they are NAPA reman alternators - and now it need another as it is not putting out the correct amps - it's under...

Hey Guys, I have a few questions and hopefully someone has run into this problem - last week I started my dart and it was running excellently. I pulled it out of the garage and let it sit running to warm it up. As it was running all of a sudden it started to stumble really bad. I thought it...

Hey Guys, just finished putting a new temp gauge in the cluster of my 68 Dart GT - old one didn't work but once and then never again - bought the new gauge from Classic Industries - everything hooked up and cluster back in dash. When I turn on the key - the temp gauge needle goes all the way...

Hey Everyone, Has anyone repainted the black "Dodge" lettering on the trunk finish panel? Is there any type of stencil that matches the lettering that I can use to mask off the lettering so I can repaint the black?

Hi Everyone, Ready to order Center Caps for my 14" SBP Rallye Rims. I bought these rims from a local guy who had them on his 69 Barracuda. My question is this: Are all the Cone Style Rallye Center Caps (SBP) the same size no matter what year caps I buy just as long as they are SBP? - I have a...

Hey Guys I had to replace the water pump and the intake gaskets on my 318 V8. The intake was plug with carbon completely - had that cleaned - started car last night and she'll burn the tires off in an instant ! My question is this: I put the timing light on it and the line in the harmonic...

Hey Everyone Thanks for all the info you have given me but I am still a little confused ..........What I am trying to accomplish is to have a little wider tire on the rear of my 68 dart gt.......... right now I have P205/70R14 tires on a set of Rally 14" SBP rims which I assume have the factory...

Hey Everyone, Has anyone ever used a company named " themorpardude.com" to get the rally rims ? I am looking at the 14" rally SBP in a 6" width - I would like to have a slightly wider rim on the rear of my dart providing it doesn't scrape either the leaf springs or the inner wheel opening...

Hey guys - need a little help I thought the reman starter was bad as when I turn the key to start position nothing would happen ... do it a couple of times and then the starter would drag and then start the car- so I put a New starter on and everything fine for a couple of days and now I have...

I am in need of one seat emblem - see pic - if anyone has one to sell, please let me know thank you Mike

I had the headliner replaced on my 68 Dart Gt and the upholstery shop didn't cut the hole out for the dome light. I can feel the wire but don't know if that is exactly where to cut the headliner to fish out the wire & see where the holes are in the center brace to screw the dome light housing...

Hi Guys, I am wondering if anyone else has noticed this with their Darts - my Dart doesn't have the windshield in yet and I am trying to figure out how the lower windshield chrome molding attaches ............ there are no "nibs" on the inside edge of the cowl panel to put "clips" on and the...

Does anyone know who has the best fitting vinyl roof material on the market? I need to purchase to replace the vinyl on my roof thank you Guys! Mike

I have finished the painting on my doors - completely strip of all hardware. Now it's time to put the doors back together - which should I do first - install the belt moldings or install the vent assembly & door glass? I don't want to have to do things twice - is it possible to fit the belt...

In Richmond, VA. Full set of 4 factory dogdish/poverty cap wheelcovers/hubcaps believed orig to my 68 Dart GT which has small bolt pattern wheels. Assume should fit most any 13 or 14 inch Mopar wheel. Very straight with no rash or scratches. Only one has a minor shallow dent near the middle...

In Richmond, VA. Full set of 4 14" factory wheelcovers believed used on 68-69 Dodge Polara, Monaco and Charger. Will not fit small-bolt-pattern wheels! Very straight with a few VERY minor areas of slight scratches on edge of a couple that should buff out. A very few shallow and minor rubber...

Hey Guys need some help - so damn confused now - I need to replace the auto trans fluid lines to the radiator and looked on the bell housing for the number - according to the shop manual it should be either: 8 cyl - 318 - A-904-LA 8 cyl - 318 - A-727-A the number I see on the side of...

I have a leaking master cylinder ( 68 Dart GT manual with drum brakes) and I was considering adding a power booster to a new master cylinder. I have read somewhere on this "Brakes" category that I could use a master cylinder for a 74 Charger with manual front disc brakes as it has a larger...

I bought this back in March of this year. I have started the restoration and then had to have knee surgery so it has sat in the garage since. I have finally started back - wanted to do the mechanicals first but still can't get down on the floor so decided to start some of the body work - only...

Hi Forum Guys, As I was disassembling my 68 Dart GT I noticed that the right door bottom hinge looks to be in the correct position - the little "kick out" wheels/gears are on the top side of this hinge. When I took off the left door ( drivers) the lower hinge looks to be upside down - the...

Does anyone know if you can get a wheel like in the picture in a 4" bolt pattern? I have a 68 Dart GT and all I seem to find are 4.5 inch bolt pattern for this wheel type. thank you!

New to this site as of today ! I purchased a 68 Dodge Dart GT about 2 months ago from a local owner and will be starting the restoration very soon. Trying to get the mechanicals done first and then on the body. This is my first Mopar in 37 years ! I have never restored a Mopar but have Chevs &...

Does anyone know a good source for locating a replacement push button heat/ac module? Mine is broken and have not seen any from any parts vendors - new or used? thank you !