Search results for query: *

need one for project tks

new good used? want to raise comp on 89 360 motor tks

have 82 mirada low compession 360 89 truck roller cam motor car is auto, 370 rear gears,what cam would you pick to use?

plain assembly needed tks

want to swap 81 Imp fuel injection to 2bbl carb. cant seem to get a 2bbl manifold ,so can i use my tbi manifold an a 2bbl carter carb ? what adapter would i need? i want to get all the parts before i disable the car in driveway tks

what do you think about asking to buy parts, club guys respond, then go missing when you want to buy them?

need 2bbl intake for use with rotary A/C compressor 318 or 360 . i want it to convert my 81 imperial from fuel injected to carb. the older intakes have the heater hose located by the stat housing an no tks bolt hole for A/C bracket

needed close to zip 12590 -mid hudson valley ny- 2bbl intake for 318-360 with or without carb also linkage tks gjglover

they are the yrs that fit ,i know it s not an A body but is a mopar tks

on steering column round held on with screw needed tks gjg

changed from reg to tilt and need to change ignition key ,i have both keys how doesit get done tks gjg

87 318 2bbl ,non smog carter 2bbl , exhaust pop at idle - no miss if you power brake it , all ignition ck n ok timing on the mark what am i looking for vac leak carb issue tks gjg

does any one have a directional wire diagram for an 82 mirada ? i am trying to use a tilt column with 8 wires in my non tilt car that has 9 wires , or has anyone done this swap?tks gjg

my add went missing. i need driver side door glass for an 82 mirada tks

my lock does not have the tabs to depress so i can get the lock out. i want to use my old lock n key for a new door help please gjg

on my 87 the sun visor has no tension at the pivot ,swing side to side ,is there any way to tighten it up tks gjg

anybody know how to rewind seatbelt retractor spring? or have a front belt for a 87 5th ave D/S tks gjg

removing lean burn going to chry electronic ing and need a 2bbl carb to replace the smog unit, ny idea what carb i could use.. car has A/C n cruze, auto trans tks gjg mopops

72 dart n scamp trunk lid n lower edge trim piece either or both no rust on lid or dents trim piece is in very good cond no dents all but one stud are their $ 50.00 each -can ship trim lid no also have left doors for 2dr ht 72 dart $ 20.00 each located 12590 wappinger ny

trunk lid with trim piece ( no rust trim good cond no dents with all but one stud--- 2 drivers side doors 2dr ht non post 1 one door from later year car ? am radio -driver side remote mirror points dist for 318--- exhaust manifolds -heads -block-360-rear sump oil pan n pickup -AC piping...

need parts 1989 360 van motor i need the pieces that keep the roller lifters from rotating they are held in place by a thin metal piece--thanks

2dr ht 318 many new parts see ad and pic s hudson valley craigs list $6800 obo DODGE DART

2dr ht 318- rebuilt cam holly 904 gone through- 8 3/4 355s spool rebuilt rally wheels large bolt pattern new ball joints front disc bushings paint head liner seat covers carpet yellow hood scoop located ny 12590 $ 10,000 or offers on hudson valley craigs list with pics thanks

anybody use a mustang rear in their a body car or in a f m or j body

i have a 72 swinger with a hood that has 3 holes along the front edge ( one slightly offset)and one set back that is elongated these are for the hood emblem I am trying to find out what this hood is off can anyone help -i want to get the emblem that belongs there or fill the holes and repaint...

I want to use 302 heads on a 318 they have been rebuilt- my son says they are boat anchors others say keep em i want to run a cam up grade any thoughts about using the 302 s ? thanks

72 dart -318 auto- keep breaking drivers side insert type - not going to spool type - whats the easiest and cheapest way around this issue . I don't want to make a project out of this as car. will be for sale thanks

i have a 91 dakota 2wd with a 3.9 stick and want to go with a 1972 5.2 la motor will the bellhousing and what else will work with this project? thanks geo.

on my 72 swinger the hood ornament is missing and this might not be the correct hood - standing in front of car there are 3 holes 2 inline from rt to left one slight offset along front edge and one elongated hole up from those -- any body have a guess as to what belongs there? i have no camera...

5.2 motor decked to 9.1 comp and 302 heads - whats a good cam to run?