Search results for query: *

Time to let go of my 71 Dodge Dart swinger. Original slant 6 car. 440 .30 516 heads. Ferrea valves Harland Sharp rockers Howard’s hyd roller .565/.565 295/305 duration Torker 2 intake Brawler 950 carb Full length under car headers/ 3” h pipe and black widow exhaust Built 727 tranny with reverse...

Does anybody know if I can fit double valve springs on 516 heads. I’ve got a hydraulic roller and it’s finally time to change the valve springs as it starts floating valves.motor is still in car ‍♂️ I have a set of 452 heads and they will not go on those as the casting around the valve seal is...

So I know it’s not an abody. But this is my go too lol. Taking the lean burn off of my 86 fit have. I’ve put on a brand new 2bbl none electric control ditched the distributor and put in a Chrysler electronic ignition and vacuum adv distributor. It fired right up. Ran for 20-30 seconds like...

The time has come and now I have a pocket full of Biden bucks. I’m going to stimulate the economy by getting a trans brake finally for my dart. What are you guys using? Is there a particular company you’d choose? Who to stay away from? I’m leaning towards the TCI but $850. Tranny is bb 727...

Looking for a 8.75 8 3/4 742 center section. 3rd member. Just need the case. But will take whatever. Looking for one in California. Thank you

I know it’s a truck.. but..... I took the 2bb off of my 360 and put a low deck weiand single plane on it with a brand new Holley 600. Runs super rich. There’s no vacuum leaks? I’ve changed the intake gaskets 3 times. No leaks . I’ve put on 2 different brand new Holley 600 vs. also...

So. I haven’t found anyone who has tried this only. I’ve always wanted too. Since I put black widows mufflers on my bb I’ve loved them. Had them on a v8 Audi also. No drone. So. Being the hillbilly I am. I drill a 2” hole through some eBay single chambers. Basically flowmaster super10s...

So after a 3.5 hr drive down to southern Cali For a pile of crap that the guy blatantly lied to me about. Didn’t get what I went for ‍♂️ 3.5 hrs one way with empty trailer over the grapevine. Then back. Only end to up driving to a town about 30 minutes away from my house To pick up this...

So. I posted that I blew up my rear end(destroyed ring and pinion) I currently had 4.30 gear and I’m going to order new on Monday. Is anyone running a 4.56. If so what tire. Current set up is 4.30 w/ 28x11.50 or 10.50. Is anyone running a 29 or 29.5 tire with a 4.56. If so. How is it. I know...

Welp. Blew up my rear end. ‍♂️‍♂️

Car idles fine. Runs fine. As soon as I turn on nitrous fuel pump. It’s drops to just about 12v on the dot. All my grounds are good and tight. The relay is working fine. All my connections are good. Can’t find the problem Please throw those ideas this way. It drops basically a full bolt...

Sooo. Here’s a couple links for a real comparison of black widow race venoms vs the trusty old Flowmaster single chambers. Literally nothing changed on the car other than the mufflers. Mufflers were placed in the exact same location as the super 10s with dumps. Actually. I lied. The...

Black widow race venoms with roller cam. Not a lot of videos of big block mopar with black widow mufflers. So here you go. Just a idle video. Will post burnout shortly 440. Roller cam. Harland sharps. Torker2. 950 brawler carb.

Will this pass? Finally going trying to take this to my local strip after years and years. Famoso Bakersfield. But this is the only thing I’m unsure about ? The way my cell is mounted. You can clearly see my on off switch for the power kill

So. Car is 440 with msd 6al2 digital. The other day. Changed my plug wires I have the Taylor 409s. After car starts up. Idles normal. After a slight warm up. All of a sudden the rpm will jump up to about 1300-1400. And the tach will jump / rev in reverse and the engine will pop and back...

so what kind of air fuel ratio do your guys big blocks like with nitrous. I’ve been reading some say low 11s. Last time on dyno it was tuned 12.5 with 150 nx plate. Got just over 100 whp on 150 jets.. I’m going to go try to tune it best I can before I go back to dyno. I just put on a...

eddy torker intake for 440. Little dirty but works perfect. No issues. $160 obo. Possible trade for black interior pieces for 71 dart. Basically open to any trade that might spark my interest also. Looking for a 68 hemi dart hood scoop. Dash pad. I will post some more pictures all...

looking for 71 dart front driver fender Somewhere in California.

how crappy to be ripped off by a fellow member...... When you sell something on here. BE HONEST. Thanks for nothing badlilred. $165 down the toilet what a ***

so I ordered the Thompson performance powerblast plates for my 4150hp. Anyone have any testimonies

So. I have a torquer intake on top. Engine is 440 .30 over. 516 heads rebuilt . About 10:1. Slightly larger ferrea valves. Hd roller .565 on both. .295 .305 duration. Harland sharp roller 1.5 rocker. Holley 750 street HP. 150 jets in nx plate mainline kit. Stall is about 3700. 4:30 gear...

Just got my front end aligned after rebuilding front end. Is it possible to get a 71 dart 440 with 18"s to drive straight. ??? Lol. Anyone else with 18s

i have a big block converter that flashes at 4800 in my dart. It is in perfect shape. I don't know the brand. Still in my car as I do drive it occasionally. Looking to trade for a converter that stalls somewhere Between 3400-3800 or close ish. I'm located in central Ca 93257.

i have a converter that flashes at 4800. Its big block. Looking to trade someone in driving distance in California. 4800 is a big much for my set up. Needing something a bit closer to 3800-4200

So. I am about to put a new oil pump on my 440 in 71 dart. After putting it on. Can I use my accumulator to keep the oil pressure up and just start it. Then if the oil drops to much. Turn it off. Reset the accumulator with air. Repeat? Thanks. I guess mainly curiosity? I work at...

so after putting car on dyno in Bakersfield ca. Short story shorter. Floated valves at around 6200. 6400 rpm. Engine is 440. .30 over. Howards hydraulic roller.150 NX plate. 516 heads. At time on dyno it had isky adjustable rockers. Now has Harland sharps. The next day when I pulled car off...

i have a set of isky adjustable rockers for a big block. Work just fine. I upgraded to Harland sharps. I also have a pair of vintage bb valve covers. I'm looking for bb stuff. I'm in need of a bigger carb. 950-1050. I have a almost new Holley street hp 750. Will trade multiple or items for...

these valve covers where on a 413 I purchased Been using them for a while My new rockers do not fit under them. I've seen a guy on eBay selling them for a lot $$$. I'd like to get $300 obo shipped from Ca 93265. Possible trade. In looking for bin block intakes? 950-1050 carbs. Gauges and...

BB isky adjustable rockers. 1.5. I've had these for about 9 years in the condition they are in now. Off of a mild 440 516 heads 150 NX pills. I got some Harland sharps and figured it was time to update. They have been on 3 different motors and have been great. There is a little bottle of wear...

i felt the need to share I scored a brand new set of Harland sharp rocker arm assemblies for 400. Replacing the rough isky adjustables.