Search results for query: *

One of the taillights on my 67 Dart has about 1 inch of water in it. How do I fix this and prevent it from happening again. Thanks Aaron

Either the screw or the piece it screws into is stripped on the upper pivot of one of my vent (wing) windows. Is there an easy fix? I have thought about replacing the pivot and screw. How does the pivot come off? Does it just slide off of the little post? This is on a 1967 Dart, but the...

I got the trico classic wiper blades. http://www.oreillyauto.com/site/c/detail/TRIG/33150/03300.oap?year=1967&make=Dodge&model=Dart&vi=5149239&ck=Search_03300_5149239_387&pt=03300&ppt=C0047 But I can't seem to get the old ones off. This is on a 67 Dart and I assume they are still the original...

The rocker molding on my 67 GT is loose on one side, where do I get new clips? I think for the time being I will remove the trim, just so it doesn't come completely off, any tips or tricks on removing it? Any tips or tricks when it comes time to reinstall it? Thanks Aaron

I hear so much on here about the incorrect trunk weather seals(gasket). Who has the best, most accurate trunk weather seal for a 67 Dart. I am getting ready to order some parts and am wondering who to order from. Thanks Aaron

found a "f" fitting for the windheild washer hose, have the original squirters and would like to reuse them rather than pay big bucks for the repop kit. They are covered with over spray, that part shouldn't be too hard, either a light dusting in the sand cabinet or soak in some paint remover...

Both doors on my 67 Dart conv., should unlock from the inside when you pull the handle, correct? The drivers door does, the passenger door doesn't. Thanks Aaron

I am looking for the little sheetmetal (tin) nuts that hold the "DODGE" letters on hood of my 67 Dart. I know I saw them in a hardware store someplace and can't remember which one I saw them at. Found some in the HELP section of auto parts but there is only three in the size I need and I hate...

I have a couple spots that are rusty in the floor and am looking for suggestions on what to paint it with. The rust is on the cabin side of the floor, the worst part is in the passenger footwell(where the beads are) and some in the drivers foot well, neither spot appears to be rusted through...

This is my radiator yoke to crossmember brace. I am wondering if it should be shaped like this or should it be straight and just hit to many curbs? Thanks Aaron

Been a while since I took the windshield wiper motor off and I don't remember which way the steel bushing things go. It has one short side and one long side. At first I thought they mounted on engine compartment side of the wiper motor followed by a rubber spacer, then I figured out they mount...

What finish (texture)would a 273 2 barrel unsilenced air cleaner be originally? I am assuming black. Would it be wrinkle finish? Thanks Aaron

Bought a repro battery tray, and from the drcription it is coated with EPDM, what the heck is that, does it need to be painted, or would powder coat be a good alternative. I can get powder coat done at work(they only use a limited amount of colors)for I think $10. I realize I would need to...

Will be taking the 67 Dart to another body shop, when I talked to him before, he said he would patch the rusty area around the battery tray with a patch panel from a parts car he has sitting out back, I assume it would be a Duster as he restored his Duster, I don't remember what year it was...

Got my Dart back the the hack (er I mean body)shop, where it was undergoing engine compartment paint and rust repair. In repairing the rust where the near the battery tray, they cut a square out and cut half of the strap that is in the fenderwell out. I assume this strap was were the battery...

the body shop I'm taking the Dart to, mentioned blasting the undercoating out of the fenderwells and painting the fenderwells body color. Kind of on the fence on this, the undercoating is sold and seems to be holding. Just seems to me that paint would be more prone to chip in that area...

Not sure where this post belongs but since the retainers install from inside the car I put it here. Where should I look for replacement firewall insulation retainers (clips). They look kind of like a plastic nail that is about 1 1/2 long and have a head a bout 1/2 in diameter. They are listed...

Took the Dart to a body shop(friend acquaintence of mine), to get an estimate on the engine compartment (repaint and do rust repair)and paint underside of hood and trunk lid. Told me to call back in a week. Called back and he asked what I was thinking and I said "I have budgeted myself around...

Am restoring the engine compartment on my 67 Dodge Dart, well not exactly restoring just want to make it look nice enough that I'm not embarassed to open the hood. How much stuff do I need to remove. I have removed the grill, wiring harness, all relays etc., heater, windshield wiper motor...