Recent content by GTXGreasemonkey

  1. GTXGreasemonkey

    Starter not disengaging?

    Installing the diode in the circuit corrected the problem. This isn't an exact match with the factory wiring schematic. Incorporating the Mopar orange box ignition and the ballast resistor created the back current issue. The red wire from the coil to the resistor meets with the wire coming...
  2. GTXGreasemonkey

    Starter not disengaging?

    The Painless wiring was very straight forward. It's not the same as factory by design. It's incorporating the Mopar ignition that was a trick.
  3. GTXGreasemonkey

    Starter not disengaging?

    I pulled the wire long before this thread, and no power was getting anywhere. No response when the ignition was turned on.
  4. GTXGreasemonkey

    Starter not disengaging?

    After further diagnostics there "IS" power remaining when the key springs back into the run position. I talked to Painless Wiring and they recommend a diode be installed in the circuit. We agreed the diode needs to be inline on the wire that runs between the Ignition post on the starter relay...
  5. GTXGreasemonkey

    Starter not disengaging?

    I agree. I've removed and replace multiple starters dozens of times now. Is there any way to confirm this? As soon as power is disconnected i've watched the gear disengage immediately.
  6. GTXGreasemonkey

    Starter not disengaging?

    I'll take a look at this. Thank you
  7. GTXGreasemonkey

    Starter not disengaging?

    How is this adjusted? I've cleaned the bellhousing and don't believe anything should be shimmed? I've tried two MSD Starters and one Speedmaster chinese starter. All have the same issue.
  8. GTXGreasemonkey

    Starter not disengaging?

    Long story sorry. Need the details. I have a 1972 Duster with a 360 LA block and a 727. I completely rewired the car using a painless universal Mopar wiring kit. As I got to a point I could ops check the engine starting system I bumped the ignition and it fired. I finished the complete car...
  9. GTXGreasemonkey

    Headliner Bow Sets

    Are the 71 Demon bows still available? Do you know if they would work on a 72 Duster? Thanks
  10. GTXGreasemonkey

    [WANTED] Duster Headliner Bows

    Oldmanmopar, Thanks for the reply!! I am definately interested in the bows you say you have. Whatever you have that I need for installation I would take. It sounds like I should go with the bows and clips? Please PM me or attach to this thread. Thanks
  11. GTXGreasemonkey

    [WANTED] Duster Headliner Bows

    I want to get rid of the one piece cardboard headliner in my 72 duster and install a vinyl headliner. I need the bows and clips please. Thanks
  12. 1972 Plymouth Duster

    1972 Plymouth Duster

    This started out as a 72 Gold Duster. My wife wanted a car to enjoy along with my 68 GTX and a friend had this. It was her idea to take the original 340 duster look of color w/ the black hood and reverse the scheme. The car is now satin black with the M3 Moulan Rouge hood and stripes. I...
  13. GTXGreasemonkey

    Blinker issue

    That is the car that I'm finishing for my wife. She had the idea of reversing the original color scheme. So what would have been black is now M5 Moulan Rouge and the car is satin black.
  14. GTXGreasemonkey

    Blinker issue

    It ended up being the new blinker camber. The metal prongs that should make contact with the steering column when the blinker is turned on were to long. They weren't making contact. I trimmed each one and the problem was fixed. Glad when its easy.
  15. GTXGreasemonkey

    Trying to remove door locks, 72 Duster?

    Able to remove everything and replace. Thanks for the help!
See more
Back
Top