Recent content by lightweight

I've been driveing my car around town a bit, it's not totally done but fun to cruise anyway. My car does'nt have the rubber seal kit in it yet but does have the hood cowl seal, when I drive the car it smells like gas. I ran my exhaust all the way to the back hopeing this would solve the problem...

Awesome put in a jump wire started right up. Thanks. Starter has a bad high pitch noise when starting though. I may have to find a way to shim it.

I switched from a automatic 904 in my 68 dart, to a abody a833 4 speed. I got it all back together, except I have'nt hooked up the wire to the reverse lights yet. My problem is it won't start now, do I need to hook up the single wire neutral safty wire that was on the 904. I did'nt think a 4...

It's a 68 dart with a counsel shifter. Thanks for the info, I thought that one wire to the 904 was reverse.. oops. So when I disconnected the wires from the old counsel shifter that is where the reverse wire must be. Thank You.

I had a automatic 904, and switched to a 4 speed. My question is, the reverse switch on the 4 speed has a 2 prong on it, and the automatic I had had a one wire hook up. What do I need to do? Do I need to just ground one side of the 2 prong plug?

Thanks for the info, I plan on making a hump today maybe if I get ambitious enough I will. I am trying to hook up the shifter linkage, and am trying to find a picture of a 4 speed to see how the linkage goes. Thats why I asked if the support needed trimmed for the linkage to clear. Because I...

It does'nt have an over center spring, in the picture of the kit I bought, It did have the over spring but apparently u cant trust some people on ebay, to send u what u pay for. I do have a spring from the clutch fork attached just behind the starder to pull the fork back. I ended up adding one...

I have the clutch fork adjusting rod to where the play is taken out of the pedal, but not adjusted to where the fork is pushing on the throwout bearing, until the pedal is pushed. Is this right? Or is the clutch pedal pushing in to far. I just adjusted it that way to get the pedals somewhat...

No. Zbar and linkage moves nice, when the clutch is pushed in the diaphram on the pressure plate does'nt come back. The pedal works fine. The guy at summit racing asked if it was the linkage as well but the pedal and z bar seem to be working I have a spring on the z bar and the pedal comes back...

My first 4 speed install, have it all in but when I push in the clutch pedal the diaphram on the pressure plate does'nt come back out? I installed the clutch with the tag that says flywheel side towards the flywheel. When the bolts are loose on the pressure plate the diaphram releases and...

I know this sounds dumb but, I am trying to install the rod from clutch pedal to zbar, I got the kit from brewers with the clips for the clutch rod but I am not sure how they go on. The hole is offset from one side to the other so if you look directly at it u see part of the other side of the...

Is there special bolts that hold the pressure plate to the flywheel that have a shoulder or something that bottoms them out when torqued? Or some kind of spacer between the pressure plate and flywheel. I am converting my dart to a four speed and trying to install a mcleod clutch and pressure...

Does anyone know, which pilot bearing I will need for a 4 inch scat crank. I ordered the ram brass bushing from summit and it's to small. I think I am going to have to use a bearing type that goes where the converter used to sit. I'm hoping for a part number if anyone has ordered one of these. I...

Bought a 4 inch stroker kit, put it in my 40 over 318 engine, still workin out the bugs but I love it. It's runnin warm and have'nt fixed that part yet, but I can't wait to get in it and take it to the store or just around town a bit. Feels like it's got a lot of power but not set up for racing...

This is my first Year One order and definitely the last.