whitepunkonnitro

whitepunkonnitro

Well-Known Member From Murfreesboro Tn
Joined
Last seen
Messages
14,798
Reactions
890

Profile posts Latest activity Postings Post Areas About

  • M
    I sent it to your PayPal account if for some reason it's not there let me know but I'm 100% sure I put it in your PayPal account
    Retnuh22
    Hey bud. Been a while. I'm looking for the trim retainers for my 67 dart gt chrome strips on the trunk. I have the chrome... no retainers. Would you have some or know of where to go to get them? Oh, and a factory gas cap that is paintable.

    Thanks,
    Garret
    whitepunkonnitro
    whitepunkonnitro
    Unfortunately, I have neither right now. Thanks for asking, though!
    H
    Can you tell me if there is a person or company that restores stainless steel trim and polish it? I know some locals but I want to get this right the first time. Limited to High Quality .
    H
    I see that you have some 67 trunk trim for sale. I am in need of that. I am restoring a dart and I want the trim for the trunk. I have a couple of other pieces but they aren't worthy. Contact me @ [email protected]. Or callme at five zero four 256 739two. Morgan
    whitepunkonnitro
    whitepunkonnitro
    That trunk trim has been gone for a while...I neglected to mark it sold.
    I'll keep my eyes open, and let you know if I come across anything nice
    I
    Aloha, Looking for a door hinge for a 4-door '68 Dart. Drivers side rear door, lower hinge. Looks like they are the same as the front door but not positive. Saw an old posting of yours, figure it wouldn't hurt to ask. Thanks!
    F
    thanks TONY, for the canopy chrome for duster, good shape and quick shipping, done business in past and will be doing business in future.
    Curt
    I know some cranks are not drilled for a pilot bushing and wont allow for a 4spd trans to be used. It seems like I have run onto a OEM Con that wont fit into the recess in the crank of my 340. The block is a 72 but the crank is an earlier forged steel unit that was used with a 4 spd. The Trans and con were bought together used. I flushed the con and rebuilt the trans they came out of a 68 340 car ?
    whitepunkonnitro
    whitepunkonnitro
    The crank is a 67 down 273 or 318. Smaller register than 68-up
    QKFSH67
    Hey Tony, I need the spring for the headlight bucket on each side,and the adjusters..curious if you had em. I ordered some but they been on back order for awhile....it's a 67 cuda
    whitepunkonnitro
    whitepunkonnitro
    I'm sure I can hook you up.
    Just send over whatever you think is fair
    Curt
    Looking for some decent red door panels for a 67 Barracuda also need good red front arm rest.
    Curt
    whitepunkonnitro
    whitepunkonnitro
    Nothing red at all right now, but I'll keep my eyes open and let you know if I come across anything.
    Tony
    RS23VOA
    I need a drivers side door panel for my 69 Swinger 2 DR. Looks like you have one?
    whitepunkonnitro
    whitepunkonnitro
    The blue one?
    Where are you located?
    RS23VOA
    RS23VOA
    Virginia. What kind of shape is it in?
    Abodybomber
    Bought some front windshield trim,72 Scamp a year or so ago, from you... The windshield installer ,was a GM guy,bitched about Mopar,the whole time.... He was good,at installation... The trim install,confused him to hell.... I just chuckled...,and made it fit.... Thanks,Defeo...
    W
    Hi Tony, I'm looking for a wiper motor for my 1968 dart. I have a variable speed wiper switch and I think I need a 2822962, 2808801 or 3004114 motor from what I have found. Any chance you have one? Thanks, Al
    whitepunkonnitro
    whitepunkonnitro
    I definitely don't have any 3 speed or Variable motors for that right now
    DalePSC
    Hi! From scanning the forums, you likely have the part and knowledge to solve my problem. I have a 65 Dart GT, and like others can't find a gas cap. Do you have a compatible, later-model filler neck for sale, for which caps are more readily-available? Thanks in advance.
    whitepunkonnitro
    whitepunkonnitro
    I just paid $40 for a cap for my own 64.
    There aren't any later necks that you can retrofit to that body, but if you don't mind a little fabricating, I can send you a later neck that you can weld to your current tube.
    $25 shipped, if you want to go that way.
    DalePSC
    DalePSC
    Is the $40 cap readily available, or a one-only? Just a cap would be my preference, but I haven't found anything other than something custom -fabricated.
    whitepunkonnitro
    whitepunkonnitro
    No, that was good used.
    Abodybomber
    You sold me some windshield trim,a year ago....Worked out ,well Tony,that /6 Dart pass(es.!!!!) , so reeks of your early work,at C.I. NICE PASSES!!!!!
    whitepunkonnitro
    whitepunkonnitro
    Thanks man! That car is a blast in every way. Put up for the winter now, but I'm going to start working on the good motor soon. We plan on covering a lot of ground with it next year
  • Loading…
  • Loading…
  • Loading…
  • Loading…

Back
Top