csx452
Well-Known Member
What is the difference between an early A body small block k member and one for a 1972 A body? I want to swap a 360 into a slant 6 car.
small block k member differences
- Thread starter csx452
- Start date
-
the frame width is different Early A to 67 and newer A body. bound to be other issues too.
What car are you trying to put a 360 into.
there are conversion mounts for 67 and newer SB v8 into 67 and newer slant 6 K frame.
I seem to recall that Early A used the same K for slants and V8s but that needs to be verified
What car are you trying to put a 360 into.
there are conversion mounts for 67 and newer SB v8 into 67 and newer slant 6 K frame.
I seem to recall that Early A used the same K for slants and V8s but that needs to be verified
That is correct. Just one K-frame for 66-64 A-Bodies
Last edited:
csx452
Well-Known Member
I have a k member here. How do I tell what it's for. I know it's for an A body. Just not sure what years it will work for. I do know it's not a spool mount k frame.
Post a photo from above and post the mounting hole to mounting hole dimensions.
These dimensions are NOT center to center.
67 to 76
These dimensions are NOT center to center.
67 to 76
Last edited:
The early A and 67+ A-body K frames are different widths. By about 2" IIRC, the early A's are narrower. You can use @Dana67Dart 's measurements to compare.
csx452
Well-Known Member
This is what I have. It looks different than the pics from Dana67Dart to me. Or maybe it's just me.
Last edited:
csx452
Well-Known Member
Measurements
The first pic sucks. LOL! It measured at 32".
The first pic sucks. LOL! It measured at 32".
csx452
Well-Known Member
Spool mount?
Yup
csx452
Well-Known Member
Would have been nice to have when I had a 75 Scamp.
csx452
Well-Known Member
Thanks everyone for your help. I really appreciate it.
It’ll fit anything 67-76, the spool mounts are a better design, and the sway bar that runs up into the K saves quite a bit of ground clearance vs the 67-72 style sway bar.
csx452
Well-Known Member
Does anything else have to be changed to swap in this k member?
What year car are you putting it in?
the mounts that bolt to the engine
you will need the 2 thru bolts, nuts and washers
you MIGHT need the bolts, nuts and washers that bolt the mount to the engine
this post has a lot of K member info for both 67-72 and 73-76
/6 K-Frame vs. V8 K
What dana67dart said. The engine mounts have to be changed for sure.
If you have a ‘67 steering set up you’ll have to change the idler arm. Other than that, you just have to keep whatever steering set up you have complete- so, pitman and idler and center link all have to be the same year range as each other, but don’t have to match the K.
The sway bar if you have one could take some work, if you’ve got the 67-72 factory LCA’s and stock sway bar tabs a ‘73+ sway bar won’t fit them. So you either need to use the sway bar mounting tab locatio from the 73+ LCA’s (add the mounts) or use a ‘67-72 sway bar, which will mean mounting it the same way as on thr 67-72 cars. So, adding provisions to the later K for the earlier bar.
csx452
Well-Known Member
I was going to include it in the sale of my 72 /6 Swinger.
csx452
Well-Known Member
I was going to include it in the sale of my 72 Swinger / 6 car. I want to be up front on what would be involved in actually using it so the potential buyer could make an informed decision.
csx452
Well-Known Member
Lots of work.
csx452
Well-Known Member
Because it's a 72 the steering is all good no additional issues there as long as it doesn't have a sway bar.
-
Similar threads
