Search results for query: *

I'm sure it's in here somewhere, but what does it weigh now, with you in it?

Kim, I think you’re talking more about the 1-2 overlap. The OP is talking strictly 2-3 overlap. The LBA valve body can create a little bit of 1-2 overlap, which is where the dual spring servo, and second gear lever ratio can help take care some 1-2 overlap. But the LBA valve body has no bearing...

72 Duster slant 6 ---3 on the tree car steering column middle key switch housing Part # 3575 698 Date coded 1971 very good condition $40.00

I’m familiar with how suspensions work and basic front end alignment, but, after looking at the Moog bushings, I’m curious how you would adjust them once they are installed.Do you strike the tabs on the sleeve, or do you simply install them in a particular position? This is a dumb question to...

As for tightening and torque references it is 55ft lbs by the manual for 7/16 inch studs and to 65 ft lbs for 1/2 inch studs. HOWEVER: -Your wheels will likely all come loose if you torque them to 55 ft pounds. One has to keep in mind that the torque spec was for and acorn style lug nuts on a...

72 Duster slant 6 ---3 on the tree car steering wheel center piece. Black color. Not marred, cracked..... Nice condition. $40.00

Yeah right! I wish…. LOL

Well then u shouldn’t have bind up. In order for that to happen the front band comes on b4 the rear band fully releases. I would put 2 springs into the front servo. So then I suspect u don’t have enough clearance/springs in the front drum. U need bare minimum .020 thou clearance per clutch...

True, if you are restoring a car, but as a good sleeper, why not?

Yes, they are and different ways of calculating the number also. Those are not what class racers are running for hp, it is a factor to pair up racers. the real hp is much higher. Not a theoretical guy. No youtube, no calculators, no racing (my friends do that). Just built engines in the old...

Good looking pup.

Looks like someone threaded a puller in too far or used a bolt to force the pump out. If I smooth this out , whats an opinion on this not leaking/leaking behind the pump.

72 Duster slant 6 --3 on the tree car . Steering column collapsible cage tube shaft with shifter tube including the tube dust cover under the dash. Very good condition. $45.00

Thanks for the info and reply, TXOval. I did a little digging and found this: 3200 RPM Stahl Speed Trans Specialties Converter

Are you talking about the Winkle? I had a R2 and R3, they were lots of fun from a roll. Just need to watch the temps.

I'm putting the bucket seats back in my 69 Dart and have a question. I took the seats apart years ago to restore them and now that I have them back together I'm wondering if I may have installed the tracks on the opposite seats. With both seats all the way back, the passenger seat sits a little...

We are in the same age frame, I'm 68 and still having fun with my 340's. Sonny and Ronny Sox, Don Garlets and Darrell Gwynne were regulars at our annual show in Hollywood, Florida. Galen Govier showed the first few years and put on a Judging class for our judging staff. I was one of 11 to...

Lord Farquad...

Hey Tim Love your PR prep... you should kick off a thread on prepping for a long cruise

sorry only other picture I have are on the flat bed

Agree I had a 1977 Ramcharger with a 360 , it was a dog had 2 360's replaced under warranty , after that put in a 4406 pac block with a torker and 850 holley made a huge difference Truck was a blast with the 440 .

Bump

Summits wholesale division / Atech invited it's customers to free track time (9am-3pm) yesterday at Norwalk Raceway Park....so Brother Weeb and I drove our Dusters for some fun. Only about 30 cars there when we arrived so we headed right to the staging lanes. We lined up side by side....let the...

falling asleep at work.... took some allergy pills and i'm fooked..

Mobil 1 has a new 0W40 full Synthetic Super Car oil; I have been running it in my 440 and have very good oil pressure and I like the fact it lubricates very well at start up especially with my roller cam

No low band apply. It's been a long time since it was built so my memory is vague. I don't know the clearance #s but I believe it has 5 red clutches. These days, I take much more detailed photos and notes of everything I do to the car. I should have done better on tranny build day. Haven't...

I have new arp bolts to use this time around ... arp recommends 100 ft lbs and there special lube. I'll be using a composite gasket 318 with a small fire ring also . that mr gasket 1121 has such a large bore ... it's almost to the edge of the valley ... with a 3/8" gap all the way around...

Why? 4.04 vs 3.91 ID. That is .13 of an inch. Not worth the expense. 340 power was in the combination of heads, cam, compression, ignition curve, exhaust, and induction. It really is that simple. 340 blocks are a little stronger, but they are both made of good material. No one wants a...

Good am men...

Maybe this is the year of the AMX.. I just purchased a 1969 AMX, 390, 4 speed, Go-Pac car...