Search results for query: *

What is the duration at .050 for the in & ex ?

For what it is worth, during covid when the world was shut down, I almost went to go buy a "built" 383 (no proof or documentation but it looked freshly painted) for $600 so I assumed it would at least just be a core. It sold almost immediately and popped up a week later with someone else trying...

I was just lookin' at SCTA site Bonneville Speedweek they have changed the fuel situation from previous. No more VP truck onsite. Bring your own or order it ahead of time.

Not sure how much this will help you but it's tough out there right now. I've had a 440 hp core with fully forged internals for sale for a while now at what I thought was a giveaway price and I opened it up so that the whole thing could be inspected and all I have gotten is people offering scrap...

Morning all and a happy Friday to ya.

Good Morning everyone. Late start as I just have a couple hours to put in. Half done now. Plan to work on the Charger today and tomorrow. I still hope to paint the chassis 4th of July week. Long ways to go for that!

Every state is different. I have a 75 car that a PO had changed out dash pads and thus the vin was left on that swapped in dash. It came into Tx from out of state so it required the Tx DPS to check it out and they saw the issue. TX DPS then stamped their vin on the B pillow and issued a Tx...

Im showing this one as its has 65 on it. So the one he needs will show 64 as the first one I posted. Kim

I'm thinking it best to make sure the bracket is moved evenly to keep the alternator pulley parallel to the pump and crank pulleys.

A lot to consider here. Cooler months/low humidity I run 180 consistently. Now that we are in the mid/high 90's, I'll stick at 180 for a bit then spikes to 210/220 especially at idle/WOT, which is still acceptable but don't want to push it on a long haul. Going to stick with a manual fan/shroud...

It was 120 in Death Valley yesterday, bout normal :lol:

Dang, heat wave in the south.

Direct them over to them spots in the lawn that need mowin' :lol:

Four of these little dudes in the yard this morning.

There is no doubt that the dyno carb was very rich, and if I was just after horsepower numbers, changing jets or air bleeds would have definitely improved things, but my main goal was dialing in my own carb.

Yes.. had someone ask me to stop there and grab fries for them. I hadn't been there in over 15 years maybe. Same thing. But I ordered at the kiosk and waited... then found out they didn't start the order because I had to flag down one of the employees hiding in the back to pay at the...

This is a Pair Of Mopar Small Block Head Gaskets. I bought them for our 340 years ago and never used them. The 340 is gone, the head gaskets are still here. :) $30.00. Local pickup, or buyer pays shipping.

interesting about the strut rod bushings, as I replaced mine when I did my suspension rebuild w/energy suspension ones. I noticed once I got it back together I have significantly more clearance to the front lower edge of my front fender that I did before the rebuild, to the point where the...

Hi how do i delete my ad and post a new ad because I am lowering the price thank you

Yes. There’s actually an extra rear seat and an extra front bucket seat that come with.

I know you said the interoir was shot is it all there to be able to be redone

I 210 in the Sunland/San Fernando Valley area, some of them bridges got my concrete in them :D and the base under the pavement too :lol:

That would be amazing if there was a way to pull that off! The cops would be busy, that's for sure! Lol For just that event, you could show up as a guest. The club is the Detroit area chapter of Twisted Axle Car Club, it's a few bucks for a new member, you get a shirt, a sticker for your...

The one large hole and one smaller is the normal small block/Torque Flight starter. I’m running one on my 5.9/42rh even. Curious why it won’t fit yours.

I am going to try the most forward holes on the tracks and put a spacer under the front two studs to 'lean back' a smidge as @Cuda Al suggested earlier. If I go down the road of fabrication, you can get some inexpensive sliders and mount them on whatever type of riser you choose. I hesitate to...

First, make sure you have all the necessary documents with you. This usually includes your identification, proof of insurance, and any paperwork related to the car, like a bill of sale or previous title. When you get to the DMV, you'll probably need to fill out a title application form. If you...

The price paid for this or pretty much anything else is the amount someone is willing to give for it. Bottom line reality.

Keeping it real. I'm from NJ too. North Jersey. We tell it as it is. On the other side of Madison I was going to buy a coffee and some fries at the McD's I stopped at to use the head. I figure its only fair to throw 'em some business for using the restroom. There's no fricken cashier! 5...

If no one quotes, then you have no indication that there are replies unless you go back to the post and check. Don’t know what tools you have, but I used a 4 inch grinder to take the shoulders off of 2 nuts. Then put them on a bolt and stuck that in my drill press and used the grinder and a...

It's Falcon Friday! Good morning :D :realcrazy: