Search results for query: *

Part #70059AI would take two if anyone has them.

PM sent.

Need a full set please.

Looking for this style please. Will need to be shipped. Thank you.

I put this in from underneath by myself, into a "1971" Dart. Didn't have the shaker on, but it did have the factory style cast iron exhaust manifolds on. There was no paint transfer anywhere. It goes in pretty slick and quick, and quite honestly, I doubt I will ever put an engine in from the...

Thanks for the replies, but I am out of my depth here if I can't find an exact replacement. I've called a real electrician to come in next week, figure out what's what and get it fixed. Cheers.

Believe me, I have searched on line. I'm not lazy, and have sent out many, many emails, few of which were replied to. Radwell listed one, but doesn't actually have one, or I would have bought it. Replacing the starter is about $1000 CDN, and is a direct replacement, not really any sort up...

I need some help here. I have been looking for months for a relay switch for my air compressor. All I have found so far is the complete starter, which is way more than I want to spend. I need a Siemens #48EH18A6S2 relay, or it's direct equivalent. This one is discontinued. I would prefer a new...

Hope this helps. Just to be clear. I have an excellent bodyman who performed this work. I do not possess the talent for this type of work.

Thank you very much.

Looking for the regular one. Used is fine, just no extra holes please.

Looking for the thin trim that goes down the side of a 1968 2 door post Dart side trim. Pictures are from the internet to show the location I am referring to, as well as to give an indication what it may look like. Shipping will be to Canada. In advance, thanks for looking.

I need 1 Wiseco piston, part # 5060A7. Fits 360 and it's .070 thou over. Thank you for any leads at all.

I don't have what you are looking for, but if you should stumble across a 5060A7 in your search, I'd sure appreciate it if you'd keep me in mind. You probably have the same problem I do, Wiseco discontinued and have none left (so they say). Good luck in your search, I'll keep my eyes open for...

Does it have a date code?

So, a couple things. Are you sure it's a STR-14 and not an STR-14-6? They look very very similar, but the tops don't interchange. I have an STR-14-6 (top and bottom), that I had a machine shop make me an STR-14 top for. It wasn't cheap, but they did it right. I gave them both the STR-14-6 bottom...

Sorry. Forgot to do an update. Couple of small teething problems, but nothing significant at all. Runs great.

I don't see the part # KBD-3500 on my Jesel belt drive anywhere, but I did have this one on my 540 Blower car. Low usage on the belt ($110.00)and the one seal ($100.00)was just replaced. It says SPD38670 on the pulley. I'd like $850 USD, plus shipping please.

All of them list them, no one has them in stock.

I need a complete set of crossram linkage for a Mopar Hemi intake with Holley carbs.

Friends car recently done.

Genuine NEW MoPar 1970 Plymouth Dodge 340 LH EXHAUST GASKET HEAT SHIELD 2946105 - make sure your sitting down.

I need a RH (passenger side) front inner fender well. An AMD would be awesome, but an excellent factory used one, rust free and straight as well as drilled properly would work too. This is to fit a 1971 Dart. Shipping to Canada.

Can you post a picture and a price please Dave.

Thanks. I 'll look it up.

Not really sure - except that maybe the round one fits better when it is installed. It's just what it should have, so I'll start there. I have pedals thanks

Looking for a 1964/5 Barracuda 4 speed tunnel/hump. It's the one that has the round hole, not the typical oval one. Need it shipped to Canada. Thanks

Carshow pics