Search results for query: big block radiator

Looking for fast tory radiator for my 68 dart big block

I have a O33 radiator for a 1968 Dart or Barracuda Hemi or big block car. This radiator needs to be restored but is in very good shape. I’m asking $1250. I’m in Bucks county PA and would prefer pick up.

I put a 76 440 motorhome in my 75 duster. I am looking for a reasonably priced aluminum radiator. Any thoughts? It is stock except for the intake . Thanks Guys!

What vendor would I use. The original dash controls are in place. The old compressor and lines are gone. I have a 4 core 64 dodge radiator in use. The 413 is similar to the 440 design. Has anyone installed A/C with big block in 74 A body? I've seen many references to Vintage Air. thanks...

Thought I would share some pictures as I recent mocked up the 22" Cold Case Radiator in my 68 Dart with a big block. I am running an electric water pump in a factory style aluminum housing and the fans and shroud were made to make it fit. (I tried a single 16" electric fan to start with, but...

I am trying to drain my coolant before replacing my intake manifold. My 340 coolant plugs wont budge and I don’t want to brake them and have to pull the motor as it would be to tight to drill and tap under there. So I drained from the lower radiator drain **** and also got the rear up as high...

This is a stock hose for a 340/AC car, cut up and 1 1/2 pipe 90 degree elbow

Getting ready to install my rebuilt engine and I am having a hard time with the cooling system. My original radiator has a big crack in it and I am missing the fan and shroud. I thought I could just simply get an aftermarket radiator and buy the fan/shroud. Its like I opened up Pamdora's box...

Carter BBDs good cores and better , move freely, $50 ea Maybe sme Carter BBS one barrels too. 62 and 64 3 speed manual trans $100 A230 3 speed trans, with slant bell, inspection cover shifter and linkage $250 Slant bells $35 Lots of 2 bblair cleaners, a couple early ones correct for 62 and 64...

I'm in the process of gathering parts to install a 440 and automatic in my 63 Dart. I'm wondering if anyone has done this and if so, does the trans tunnel need to be enlarged to fit the automatic? The car is currently straight six with three on the tree. Thank you for any information you can...

I'm looking for a clean, functioning 70-72 big block 22" radiator with 3 or 4 cores. I want a radiator that works and looks nice that I can install as-is. I don't want one that needs to be re-cored nor an aluminum radiator. An aftermarket radiator that looks like a factory radiator is o.k.

First year 1973 Dodge D100 Club Cab pickup truck. Factory 400 big block truck with power steering, power disc brakes, air conditioning, electronic ignition, swaybar on D100 suspension, 727 heavy Duty automatic transmission, heavy duty radiator, 8 3/4 rearend, 4.5 five lug pattern, buddy rear...

Cast iron big block water pump housing. #3698468 casting with passenger's side radiator hose. It's pretty crusty and will need a good clean up. $45 shipped from West Sacramento, CA (PP F&F, postal money order, or check). Or $20 local pick up.

UPDATE 12.14.2023 Welcome, for those of you reading this build for the first time, I figured I would do a little update on the build progress. It has been a little over 8 months since the preservation began and a lot has happened. The engine was rebuilt by Sean who owns SB Engine and Machine in...

Curious what everyone is running as well as clearance w/ mechanical water pump and overall performance. I’m thinking of going with the Champion 26” 3 row w/fans and shroud but need to dig deeper into depth of the assembly (engine is not in car yet). Champion-CC374B-374FS12SP But I also see a...

Hi looking to get a new 3 row radiator in my slant six to 360 conversion. I'm noticing that the slanty rad lower hose connection comes out on the passenger side while the v8 replacement comes out on the drivers side . The slanty seems to almost line up with the water pump . Is there a known...

I picked up this 1968 Barracuda fastback with thoughts of building it into a race car but now i'm not sure I should go that route. Its originally a 383/4spd formula S. Although its been raped of more common parts, its still has the BB K frame,8-3/4 rear,clutch pedal and rear torque boxes. It has...

Looking for an original or Glen Ray 2898033 Big Block 1968 radiator. This is for a numbers matching 1968 Dart GTS Thanks for any help.

New 440 Source big block water pump. This the pass side lower hose unit correct for 74-up B-body and 72-93 truck. Can also be used with a small block radiator to get that hose away from the oil filter on other B/E bodies. 125.00 Plus shipping Free delivery to the following shows with pre-paid...

On a 1973 340 26” radiator the fan shroud part #3673820 seems to be very hard to find. Will the readily available reproduction #2998326 shroud fit? The reproduction is listed as B & E body big block. There are also other 26” reproduction shrouds being made just wondering if any will fit the a...

Recored 2998978 radiator. This was in my 58 Parisienne convertible and had approximately 150 miles on it since being recored. Cooled the big block in the Pontiac beautifully. I replaced it with an aluminum rad as I thought this needed to go back into a car it belonged in. $550.

I'm looking for a factory 22" big block radiator for my 69 Dart. I need one with the fittings for automatic transmission cooling lines. I can pick up at the Nats to avoid the hassle and cost of shipping.

When I bought my 69 Barracuda about 33 years ago, it had a pretty good sized radiator in it. I assumed it was a 22" out of a B or E model. It did JUST fit from side to side, but about 1.5-2" of the core was blocked on each side. I stripped the entire car down to bare metal both times I painted...

I have a Demon with a 340 stroked to 408 CI sitting in my garage. What would you think would be the minimum radiator capacity to keep running/cruising temperatures down? It has what looks to be a six cylinder size aluminum 3 row radiator in it now. It is constantly getting hot when driving...

Hi everyone Whats the best combo of parts to use to copy the cooling system used in a 1969 M code 440 car automatic car Best rad Best fan shroud Best fan Also where would be the best place to find these items Thanks everyone

I decided to make some heat shields to block off the big space on either side of the hood latch. While I'm not even close to having an over heating issue, it can't hurt to divert more air through the radiator. They are some big spaces too. I used some corrugated plastic from a parts display...

I'm going to create a collection of information that I have countless questions about. To start it off, I'm 17 years old and just started learning about American muscle cars. I have flipped a few cars in the past, but nothing to the extent of what l've been working on lately. I have a single-bay...

Hello, Building 67 Dart 383 4 speed car. Bought this radiator at a swap meet last year. Now its time to install it. I believe the guy said it was off of 67-68 bb cuda auto, who knows? Although I would like to know? Looking for a fan shroud that would be acceptable for my application. This rad...

70 Dart, warmed over 360 magnum, probably about 370 hp I remember reading here that straight fan sucked about 15 hp, I didn't remember that the hp loss for using a clutch fan was mentioned. I have a 27 inch plus long x 21 tall aluminum 2 core radiator, biggest one that would fit, it's...

The '66 Valiant I recently finished went on a long interstate trip last weekend and it was rather a "cool" day for us in the low 90's. It is a 360 that has aluminum Edelbrock heads and a 4 core radiator by Bob at Glenray.. factory shroud, correct factory direct drive 7 blade fan, all lower...