Search results for query: *

The parts for sale are located in Jasper, TX. They are from a1968 Dodge Dart GT with 273 cid engine and include the following: 1) Accelerator pedal with carb cable and mounting nuts. 2) Small block engine parts - alternator brackets / shim, coil bracket, carb return spring bracket, distributor...

This is an original "driver" side rear tail light lens. Price: $30.00 which includes shipping within continental USA.

From 68 Dodge Dart GT. Believe pads will fit 67 and 68 Darts, Barracudas and Valiants. Parts are located in SE Texas. All are in very good condition to include mounting studs. All mounting nuts and bolts included. Price: $220 shipped (continental USA only).

I’m about to start the installation of a FiTech EFI 30002 unit on a 68 Dodge with a 440 cid engine. The only location I can identify for the FiTech coolant temp sensor is in the water pump. Using that port will require disabling the existing coolant temp gauge. I’d rather not disable the gauge...

Frame and padding in good condition. Has glove box door. Located in Jasper, TX. No shipping, must pick up. PM me to discuss pick up / cost. $110 if I pull it. Cheaper if you pull it.

Parts are from a 1968 Dodge Dart GT. Parts will require cleaning and / or painting. I prefer PayPal but will accept money orders. PM me if you have questions. Shipping quoted is to US locations only. Item 1: Interior parts - Driver rear, interior finish panel bracket and two GT door emblems...

Parts are from a 1968 Dodge Dart GT with a 273 cid engine. Parts will require cleaning / painting. I prefer PayPal but will accept money orders. PM me if you have questions. Shipping quoted is to US locations only. Item 1: Throttle foot pedal assembly with throttle linkage, $45 shipped. Item...

From 68 Dart GT with 276 engine / 2 barrel carb. Should fit 68 - 74 Dart, Demon, Duster & Scamp. $55.00 shipped (USA). I prefer PayPal but will accept Money Order. PM me if you have questions.

Will need to be sand blasted / painted. One of the brake master cylinder mounting studs will need to be replaced. Located in SE Texas. I prefer PayPal, will accept money order. Price $80 plus shipping.

Came off of vehicle with manual steering. Located in SE Texas. I prefer PayPal, will accept money order. Price $90 plus shipping.

All parts are located in SE Texas. I prefer PayPal but will accept USPS Money Orders. Prices do not include shipping. 1) 68-70 A/B body, convertible top latches - $25.00 2) Left rear tail light lens - $30.00 3) Left rear tail light assembly - $30.00 4) Dash ash tray mount - $15.00 5)...

I have a 68 Dart with a 340 engine. I recently acquired an original 22 inch auto / AC radiator (Part # 2898031) to install after having it rebuilt. When inspecting it I noticed that 8/32 bolts were last used to mount the shroud to the radiator. Are 8/32 bolts the correct size? If so and you have...

Driver quality emblem. Missing one stud on rear. $25 shipped to lower 48 states. I prefer PayPal but will accept USPS Money Order. Part located in SE Texas.

AC / Heater controller plus mounting bracket from 1968 Dodge Dart plus second controller and hoses. Cost: $65.00 shipped to lower 48 states. Parts are located in SE Texas. I prefer PayPal but will accept USPS money order.

Part is located in SE Texas. I prefer PayPal but will accept USPS Money Orders. PM me with questions. SB, 18 inch, 4 blade radiator fan with 2 3/8 inches spacer, came off a 1968, 318 engine: $40 shipped to lower 48 states. Thanks for looking!

All parts are located in SE Texas. Flat rate for shipping one WP pulley is $10.00; crank pulley $15.00 to lower 48 states. Crank pulleys are from RB / BB engines. I prefer PayPal but will accept USPS Money Orders. 1) Crank pulley, four groove, diameter 7 ¼ inches, depth 3 3/4 inches, 6...

Fits Mopar Big Block and RB engines. Perimeter Bolt / Stock Height. Mounted once but engine was not run. Located in SE Texas. $105.00 shipped to lower 48 states. I accept PayPal and USPS Money Orders. PM me if you have questions. Thanks for looking!

Parts located in SE Texas. Right and left upper door and ¼ windows stainless moldings. No dings or major scratches. Will look like new with a bit of polishing. Some mounting clips need replacing. I prefer payment via PayPal but will accept USPS money order. $95.00 includes shipping (to lower 48...

Locate in SE Texas. Recently swapped for 750 cfm unit. Operates and idles well. $65 plus shipping. I prefer PayPal but will accept USPS money order. PM me if interested or if you have questions. Thanks, Bob

Located in SE Texas. $40 plus shipping.

Located in SE Texas. Includes mounting brackets. $205 shipped to lower 48 states.

Hi all, Have heat shields from a 273, will they bolt onto a 340? The shields that protect the plug wires on the drivers side. Really appreciate the insight.

Hi: I'm attempting to find the chrome knobs that fit the heater controller levers of a 68 Dart. I suspect other years will work. Please PM me if you have any you'd care to part with or if you know where I can purchase said knobs. Thanks, Bob

The title for this post says it all. I need a new Ignition Switch Lamp Time Delay Relay for our 1968 Dart. If you have the part number and a source for said relay it would be greatly appreciate. Thanks, Bob

While replacing hoses on a 1969 340 cid engine I discovered the intake manifold nipple OD is 1 inch while the water pumper nipple OD is 7/8 inch. See attached picture. As you might expect the replacement hose (Gates 19605) fits the water pump perfectly but not the intake manifold. My plan is...

Very clean COLUMN shift 727 transmission tail stock, part # 402819. Located in SE Texas. Has new rear seal. Price: $45.00. I prefer PayPal. Thanks for your interest. Bob Mitchell

The latch works well. I ran it through a chemical bath to remove any rust. Support needs to be sand blasted and repainted. Spring is in good condition. Asking $40 plus shipping. Located in SE Texas. Send me a PM here if interested. Thanks, Dodge Car Man

Three of the four wheel covers are in good condition. The fourth took a hit. Asking $45 plus shipping. Located in SE Texas. I'll even wash them before shipping them. Send me a PM if interested. Thanks, Dodge Car Man

This is a first time occurrence for me. The insulation material in the ignition control module melted (see comparison picture). It made a terrible mess and of course screwed up the paint. I’ve tried every solvent I have to get rid of the super sticky residue. Does anyone know of a product that...

Rescued this old girl from a thicket a couple days ago. I still need to decode the VIN tag. Most of the stainless trim to including that for a vinyl top is there and in good condition. Door and rear windows appear to be reusable. Upper inner door panels are good. Other than the vinyl top...