Search results for query: *

Does anyone know what years had the jack slots and which didn't. I have one of each for my 72 Demon and would like to use the correct one. Thanks Jeff

Hey looking for opinions on gasket brands. I've have a leak issue with my 73 Scamp. Pulled windshield and dash resonantly to remedy this. I have used Precision gaskets in the past but they seem to be small and stretched out in the corners. Any other brands recommended.

I have 2 left front fenders 1 fiberglass and 1 steel. Steel 1 has pitting but no holes. Located Kitchener Ontario Canada. $75 each or make an offer.

Hey I have a 72 Demon with the full Phoenix graphics package in matte black. When waxing should it be avoided or just wax right over it. Made the mistake of waxing over flat black in my youth and it was a bugger to get off.

Hi does anyone know if lash can be measured at the wheel stud or pinion flange. I thought mine felt sloppy when I took the drive shaft out. Measured on a wheel stud. .023 Thanks Jeff

Hi looking for the front bumper filler ends. I think 73 74 will fit. They go between filler and fender.

Hi I have 2 318's Scamp and Aspen also a 340 Demon. All with Mopar performance ignition. All 3 have a low rpm or idle stumble. All have different carbs. Spark plugs on the black side so lean is not the issue. At the moment I am increasing plug gap on 340 from .35 to .45. Anyone else experience this.

I am doing front suspension bushings in my 72 Demon and found front of strut rod has a grove worn in it from rubbing on K frame. Was thinking of migging and grinding for repair. Has anyone tried this before or would it weaken it. Thanks Jeff

Hey all who read this Having issue with my 72 Demon. I have a 2537349 manual steering box, new pitman arm which I checked same as one I removed. I centered box installed arm and it is offset to right. I have to have tie rod ends all the way in on one side and out on other to get wheels straight...

Hi All I have a 3spd floor shift manual trans in my Demon. The shifter doesn't line up properly in the hump. Boot will not go on. Is there a shim to move shifter to the left to center it. Also does the boot mount to the floor under carpet. thanks, Jeff

Hi everyone I've been working on the wiring of my 72 Demon. Got most of it worked out. Found that there is a resistor/diode in the parking break circuit and also goes to relay under glove box. Don't know what either is for. The wiring diagrams I have are little confusing there. thanks Jeff

A-body 7.25 rear axle complete. 2.76 gears.

Hi everyone I have a question about correct color of Demon fender emblem. I have seen them with yellow lettering and others with white. My Demon is painted factory gold and I don't know which would be correct. Thanks Jeff

Good day everyone Having problems with 72 Demon project. Had trouble finding cardboard headliner so I purchased bow set up. Low and behold no holes for the clips. Any one have good pics on where exactly they go or any other ideas on the subject? Thanks Jeff

Hey everyone long story but I'll try and make it short. Needed a 318 for my wife's 79 Aspen. I Payed $200 for a runner that turned out to totaled. That said out of all the parts that I have I'm going to build one for my Scamp and use the motor from it in the Aspen. I've got a 79 short block...

Does anyone know if Passon has the 5 spd on the market yet. If so how much.

Does any one know if using a motor from a manual car in a automatic will cause balancing problems from changing flywheel to torque converter.

Hey I'm looking for a front bumper with brackets for my 73 scamp. Was told 74 would also fit but has extra bumper bolt. Located in southern Ontario Kitchener to be exact. Thanks Jeff

I've been working on my 72 demon wiring and I've found discrepancy in the wiring diagrams. The 72 chassis manual and the 73 diagram I got off the mitchell program show the horn and the starter relay are both dark green with red tracer. The are L & T at bulkhead connector. They seem to be...

hey every one having an issue with the rear center body line of my 72 demon. does anyone know if it curves over the rear wheel well or is it straight. thanks Jeff:dontknow:

Hey everyone. Just changed my scamp to a 727 and 8 3/4. Thought I would check and see if anyone close to Kitchener would have a drive shaft to fit before I have one cut. Don't know cost vs cost never had one done before. Also looking for 323 or 355 gears and suregrip for 489 case or consider...

which 727 is correct for an A-Body long or short tail

looking for A-body large bolt axles shipping to N2G 3C6 Ontario. Thanks Jeff

Looking for throttle and spring bracket for my 340 manual tranny. I'm in Ontario N2G 3C6. Thanks Jeff

Located in Kitchener Ontario. Motor is out of a 78 aspen. Was told it hasn't run for at least 5 yrs. Odometer read just over 100k. Asking 200.00 obo. Pick up only. I have video of it running. Can't load pic at the moment will try again.

Hi looking for clutch dust cover for a 72 demon 340 3spd. Would have to be shipped to Ontario Canada. Jeff

Anyone have any pics of under side where left exhaust passes through from manifold on a stock 340 4 spd A body:happy2: mines a 72 demon.

I have the mopar performance kit with the bell housing included. It lines up front to back but sits about an in" too high and the arm too the fork is too short. Amy one run into this problem. 72 Demon340 3spd manual. Jeff

On auto trannys there are brackets that tie the engine to tranny do manual trannys use them. thanks ahead Jeff

Any one know of a good kit to hold down left side of motor with the biscuit style motor mounts that allows a little comfort.:book: