Search results for query: *

I just put new springs on 69 cuda and now I’m getting axle wrap, not sure where to go from here. Any ideas?

I’m going to install new leaf springs today, I’ve heard of using stock brackets, anyone know about this? Does anyone have any tips?

On my ID pad it reads pp833041 503 Not sure how to read that date any help is appreciated

drivers side rear drum grabs when moving forward, but not in reverse. Car is on jackstands and the parking brake cable is disconnected. brake adjuster is all the way retracted. brakes are 10".

Looking for a pair of b body frame rails

how do I know what my idle speed target should be on a 383 .30 over rpm performer intake, edelbrock1411 carb, summit cam, tti headers

69 cuda 383 rpm performer intake edelbrock 1411 carb 10:5 to 1, summit cam not sure what my timing or idle should be to get a good starting point, car will start and run but not long, initial timing is good

Looking for a header panel that is in descent shape, I prefer a steel one

Looking for a heater box and controls for 69 cuda, driver quality is good enough

Looking to see what a part attaches the glass to the regulator

new bell housing flywheel and clutch, now the mini starter turns engine about a 1/4 turn and stops. any ideas?

How do you get a title from a bill of sale in ohio

i am trying to dial in the timing on a 383 that has edelbrock intake carb, and mild cam. not sure where i should be on degrees, also i was told you cant set timing on a msd ignition set up. i have top dead center and car starts right up. how many rps should i be running at idle? any help...

i have a two prong four speed switch for reverse lights, does the switch ground itself through the trans and both prongs are signal wires, or is one prong a ground and other signal. im dumb when it comes to wireing any help would be great

looking for a bucket seat hinge cover, lo tone horn

looking for a rear floor pan that goes under the rear seat for a 71 demon, i believe that they are 108 wheel base. anybody parting out one?

i just left the indy cylinder head show, and still nedd some parts, marker reflectors, windshield trim, reverse light bezel, wiper arms, bucket seat hinge covers color doesnt matter but i nees one pair and one rt side, pair of door sills that can be nice driver quality,two chrome bucket seat...

Is it possible to make it work, or should I just buy a 69 dash harness? I already have the 72 harness but before I buy relays and buzzers I need some opinions

Looking for the clips that hold the moulding in the cargo area of a fastback cuda

I have called r/t specialties, emailed photos, measurements, and so on. They can never seem to find the time to get back with me. So I am looking for these clips so I can move forward, does anyone know what they are called, where I can find them, wanna sell them or any guidance The clips go on...

Looking for seat foam for a 69 barracuda, dartt may be the same in 68 -69 thanks.

I noticed im missing some clips that hold the trim in the cargo area of a fastback barracuda, are the trim clips specific to that trim or could I use other types of clips? Anyone know

im running a amp power wire through my fire wall, and was wondering if I should drill a new hole or is there a hole already there I can use?

I am trying to figure out where the bulb bracket bolts to on a 69 fastback, thanks again

Looking to purchase seat foam for 69 cuda bucket seats

Recovering rear seat on fastback cuda, not sure if the chrome trim goes all the way around, or just the top and sides. The seat has holes all the way around but I could only find three pieces of trim the top and corners. Could it be that my seat is not a folding seat and trim doesnt go...

What are they, where do they go, thanks for the help

I am having trouble with my clutch system binding up. I have the tti headers on a 383 four speed with a lakewood bellhousing. The z- bar is tti's, but it is rubbing against the side of the bellhousing, and my clutch rod going thru the floor is rubbing the drivers side of the big oval hole. Looks...

Im looking for a parking brake cable retaining clip for a 69 barracuda. Its located under the dash and connects to the bracket that the brake lever attatches to. Its he clip that hooks on one end and bolts on the other end. I took one from a 72 dart but it must be different.

looking for a descent 69 cuda rear harness with the pillar lights, or maybe just the pillar light harness.