Search results for query: *

Rust free Car. Plus 1970 parts car. Lots of good parts. No engine. $6,500 Dayton, OH

bought a 76 A-body...Ran great for 3 days,,,,but now it starts right up,runs for about 10 seconds then dies?! Previous owner replaced carb,gas tank,pick-up,all gas lines....Horn wire was unhooked,,because it blows when the the key switch is turned on....I installed a electric fuel pump,,,still...

More pictures continued!!! pic. #1 good flat work surface that`s 15/10,000ths. (don`t have to be that close) #2 ripples from rolling,must be smoothed. #3 4" skinny(V.W.) #4 check stock wheel before anything #5 compare stock run-out to tacked wheel #6 wifes 5th avenue #7 choose...

Here are the pictures that go to the first post. #1 4" V.W.on the left mopar 5-1/2" right #2 same #3 same #4 after plasma cut grind even ( only rears) #5 check edges w/ feeler gauge,,grind down high spots #6 same as #5 #7 Cut just behind the weld,,don`t try to cut weld.(it`s too deep) #8...

Went back too Springfield,Oh.,swap meet!!!big...Biiig,,,BBIIIGGggg,disapointment!! I tell myself i`m not going next year,i`m going to stick to my guns this time...They should call it Springfield,Oh.,(flea market!!!) Suppose to be auto re-lated items only,now it`s anything goes,i seen baby...

Springfield,Ohio...One of the largest in these parts..Gonna go ,if it does`nt rain..Need anything?? viet-vet..

Springfield,Ohio.....Cars and parts one of the largest in these parts...Gonna go tomorrow if it don`t rain! need anything? Sept.10th-12th. viet-vet..

might help someone; The"318-3" part#2668810 though discontinued, is stronger then the forged 340 crank! These cranks were refered to as 318 truck crank, found in the late 60s early 70s 1 ton dual wheel dodge trucks.Happen to have one,found another one but the salvage yard said i`d have to take...

Hope this helps someone. decited to mini tub 6cyl. 75 dart. took a pair of 7x15 steel rims,took them to black smith shop..had them cut them in two.on a lath.. 1/2" in front of center section. used 1/8"x4" flat steel,had them roll it same diameter as the inside of the rim..ALL FOR $30.00. I...

Went to local swap meet last week end of may.Mostly the other brands vendors. Spotted a set of 68 dart dishes`was`nt on dis-play. Inside his trailer.No dents`dings or scraches.could use a good polish.Wanted $130.00 for the set.Is that reasonable ?

1969 dart grill (very straight) $75.oo+shipping from New Lebanon,Ohio 45345 (:

Sold

Duster L&R door panels with L&R door handles with Bezels; dated 01-74. Parts have not been painted or dyed. No tears or cracks, few small blemishes. Driver side low rear corner has been repaired. May be seatbelt damage? 2 arm rests included, not shown. 37 years old but still very nice...

Looking 4 a nice dash-pad4 70 dart,black prefered but beggers cant B choosers!! Also need pass. side fender extension( moulding)...I MIGHT HAVE SOME PARTS LET ME KNOW WHAT U NEED....THANKS.GRANDPAS TOY.

Looking for left front fender for 70'-71' dart. Any leads on one would be great. Thanks

Am looking for left front fender for 70'-71' dart. Any leads on one will be great. Thank you