Search results for query: *

Yes I did and I seated the bearing by bcranking down the nut until the shop manual said to then backed it off just a touch. Are you supposed to grease the spindle and inside of hub before installing the hub and tighten it down to seat the bearings?What could I have done wrong during the...

Hey Everyone, Been a while! Anyhow, I am hearing a clicking or cracking sound when I go around a turn in my 1972 Duster. Can anyone confirm my thoughts that it might be a bearing. Changed the bearings on both sides of front and am still getting the noise. Could it be something else? I hear...

Hello boys n girls, I need some help please! When I put the Duster( auto tranny) in reverse I get a stiff clunk or bang noise. Sounds like it comes from the rearend. I wonder if it is u joints or something internal on the rearend. Only happens when I go into reverse. Any body got any...

Hello, Can anyone tell me the pro's and con's with using a 3 speed synchromesh manual transmission behind a 318 on my 72 Duster?

I am hoping someone could tell me the correct 3 speed maual floor shift tranny would be used for the 1972 Duster with a 318. Was this tranny a synchromesh only unit and what would be the correct serial numbers or casting numbers. How would I identify a correct unit. Is there a specific size...

Thanks, I guess it takes a lot of time to get info on this forum. Or maybe no one is interested.

I am hoping to get some educated advice about an engine and tranny combo that I am considering. 318 bored 40 over stock heads redone Weiand intake with Edelbrock #1406 600cfm carb Mild cam and a 3 speed synchro on the floor What would be my best clutch kit to use for street, maybe a...

Does anyone know which 3 speed manual tranny was used behind the 318 in 1970 thru 1976 Duster. Was it a synchromesh only or did they use both. What would the serial or casting numbers be.

Ok! Yes the tranny is from a 72 Duster, main case stamping is pp230 4227 Listen, I'm trying to figure out how to use this site. When I read your message, is the little box that says QR the best way for me to respond to someone. I think I've been talking mostly to myself on this darn...

Anyone ever swap a slant 6 and a 904 to a 40 over 318 and a 3 speed synchro manual tranny? Talk to me! :pirate:

Thanks Adam, Was hoping someone might comment on my combo question for the motor and tranny install that I am wanting to do.

Nice Cuda, I am finishing a 1972 duster for my father. BLACK ON BLACK, 318 40 over with Weiand intake and Edelbrock #1406 600 cfm carb. I have been considering the lokar unit instead of finding the correct kickdown. I"m swapping from a slant6 to the aformentioned combo. How's the lokar...

Ok! Thanks for the advice and help! I am hoping some one could comment on my other questions in regards to the combination that I am looking to install. the combo is listed on my first post at the top of this page. I'm going to need to get a clutch and flywheel setup. I want this for street...

Daliant the tranny that I am looking at is an all synchromesh unit that has a 4 1/2 inch retainer bearing and a 1'' input shaft 23 spline. Would that be correct to use on a 318? Thanks! Yesteryearmotorcars

The 8.25 has more bolts on back cover than the 7.25. you should also be able to see the sheer mass difference between the two housings.

I put an 8.25 with a 3.21 suregrip from a diplomat police car in my 72 Duster. Moved perches in to match leafsprings and man, sweet, put new brake parts on and new lub. Cost me $150.00 plus time to do the welding, brake job, lub and install. WELL WORTH IT! GOOD LUCK! Yesteryearmotorcars

What are the differences between a small block v8 3 speed and the /6 3 speed manual transmissions besides the bellhousings? MOPAR or NOCAR!

Yep! Depends on year as far as mix and match! I would like to find the 2 in 1 housing! Thanks!

OK! If you are the one that left the picture of the bellhousing, say yes stupid, I am the one. LOL!!! Trying to figure this out.

So I guess your AdamR? Well I think I am figuring out how to use this site. The research that I have done on this subject has given me 2 possibilities. 1. Depends on the year of the bellhousing. 2. depends on the flywheel or clutch, can't remember which.

Hello to all MOPARS, I am confused!!! I was asking a question about 3 speed manual tranny and got this. Who is AdamR and maybe someone can tell me how to use this site. I was hoping that posting what you call a thread was the same thing as asking what we in English call asking a question...

Because that is what I want and it would be correct for this car. How do I get an answer to my question. Yes I know very little about computers and the terminology. :glasses7:

Hello all! I have a 1972 Duster currently powered with a /6 and 904. I have recently replaced the stock 7.25 rear with an 8.25 with 3.21 suregrip gears. I am planning a motor and tranny swap. I want to install a 1973 318 bored 40 over with weiand intake and an Edelbrock #1406 600 cfm carb...