Search results for query: *

SOLD Complete 273 rocker set, shafts, spacers, bolts, and pushrods for 340. The push rods are brand new, and the rockers have brand new adjusters. $200.00 SHIPPED

Gentleman and Ladies, heres my issue new cam, installed, new carb 340 engine, Ive got fire at the plugs, but im not getting any backfire thru carb,no signs its firing,yet i can see it fire, at plug,i had noticed some burns on the top of the cap at the coil wire so i replaced cap, rotor and coil...

Installing these rockers from 273 on 340 is this correct set up,I didn't find a picture

The 273 shafts appear to be the same as the hydraulic shafts on my 72 340, but the oiling holes are mutch larger on the 340, can the 340 shafts be used with the adjustable rockers, I was just speculating that there would be better oiling with bigger holes, or should i stick with the 273 shafts?

I need at least one good 273 adjustable rocker arm

Just reinstalled a new cam, and I was using my stock 1972 rockers since i got the car in 1984, needless to say they are caput, so thar being said I have installed a Hughes SEH2024AL-11 I need a set of reasonable set of roller rockers as an upgrade, Im looking for a reasonable priced set...

I forgot does the oil feed bolt go at the top right

A few months ago i flattened a cam, since then I have been working on my 69 bird. I MISS MY 340, TIME TO PUT HER BACK TOGETHER,

340 less than 600 miles on comp cams version of 484 purple shaft lifter wear and I assume trashed cam. From left to right worse to good

I have a 1972 340 Engine, freshly dipped and magnafluxed, engine checks to be good. The block has been in my possession 30 years, comes with cast crank, rods, balancer and 1 head for $500.00. I'm located in East Texas, at the corner of TX, LA,and Ark. Local Pick Up Only Private Message me for...

I have a 72 340 block, cast crank, rods, timing cover and 1 head for sale for $540.00 I am located in Atlanta, Texas at the corner of Texas/Arkansas/Louisiana. Local Pick Up Only PM me for further details.

I cant get the axle out of 8.75 unit, it may have rusted since the other side was missing an axle. Question is, I removed axle outside cover nuts, the bell housing cover wont come loose, I know that some assemblies have a large adjuster nut on them, do i need to pry this cover back. We tried to...

Need the hubs so I can replace my front drums, on my 72 340 car, needing it to fit the 10"inch drums with the 4 inch bolt pattern...Help I will consider two complete drums with hubs in good shape, should be thousands out there...

1972 Duster 340 4 inch wheel, heres the problem. Where can I purchase the Drum with the hub, Oreillys auto tried to sell me a drum with no hub,,,,,,I need to get this car back on road, and I took my old ones and put it on a flip Im working.. The Drum has no hub in which they ordered for me? I...

I need the v shaped Federal Power Steering mount to the timing cover, and the correct bolt and two to three inch spacer that the bolts runs thru....with the bolt.

Several Years ago I took my build sheet out from behind my 1972 Dusters back Seat, I new it wasn't jiving with my cars vin, I put it away and never really looked at 25 years later my son in law was asking to see it. He decoded it and says its to 1967 Charger 383 car, Crazy Business Chrysler must...

I need a pic of a 72 Duster Trunk spare Tire in its original position, with hold down and does anyone know where I can get the bolt to hold the spare down, or is it best to make one from a carriage bolt.

I know the orange is the wire is used to power the accessories, I came across a really long orange wire at the end of the harness towards the glovebox, it is long enough to reach the foot sill plate, has a brown female flat plug on it? What is it?

I have a Thermoquad 9096S in good shape boxed for several years in garage. It was in working order at the time I removed it from my 340. It has been boxed. Asking $60.00 plus shipping.

I need two- two prong door switches for my 72 Duster....

I have been working on Dash Light Power Problem and I Havent gotten anywhere, I plan to install some LEDs, but for now I have this issue. Some years ago I had removed the entire dash assembly for painting, I re installed to find that I now have no dash lights. All my fuses are good, I have turn...

Does any one have in good or bad comments about the site MOPARTS parts and Supplies I ordered a part for $114, I got billed but can get them to phone no corespondence nothing.... Anyone know these folks says St. Paul MN, physical address aint checking out.

Im needing to work on my dash lights on the original 72 dash circuit board, Im in need of the bulb sockets, but was wondering has anyone put leds in their place. The originals being quite a bit dimmer than LEDs. If so where were they purchased.

My 72 340 Duster has a small pinion 8.75 rear as most do, from reading here and there I thought the pumpkin chunk had a three digit identification, I have the casting number which ID'd it as small pinion. The only other marking i see is a X on the drivers side of the case. I plan to do gear...

I have a 318 engine which is currently built, I believe that some mods have been made to the 318, because a spare set of 318 heads and intake came with motor. How would I be able to identify the heads while the engine is together. Is the casting number under the valve pans going to identify the...

New , but opened Mopar Performance P4529797 Orange 340 plug wires. Twenty Dollars plus Shipping. Any questions PM me..

Installing 284/484 comp cam in 340. Cam Card says 104 Intake centerline, after degreeing, I'm showing 107.5. I have a 2 degree offset, should I use the 2 degree offset or order a 4 degree offset. Final question when I install the offset, will the offset be on the left side of the crank keyway...

Been looking for cam advance keys for 340, I need a set to degree my new cam, suggestions where I can buy them, Thanks

I am setting up my Air Gap on my 340, mounted my Autoguages guages and first thing I noticed was the AutoGuage water temp sensor is huge. It aint going to fit in the original sensor hole location, leaving me only one option, I purchased a Brass 3/8 tee and mounted the tee where the heater hose...

Item no longer needed