Search results for query: *

Got it yet ? If you send by Post Office ,send to Hubert.If not ,send to Monty ,the other address.Thanks !

PM sent

Needing K-H pin type calipers, brackets, pins for the 73-76 A body spindles. PM me,Thanks

Can you send mailing address to [email protected]

I tried PM but your inbox is full. I would like to buy brake parts

I live in Coahoma, about 10 miles east of Big Spring. I have a 72 Swinger with 340, 66 Belvedere II with 440 -4 spd, a few big block engines.

If you have to choose between the 22-250 or 17, the 250 hands down. Have you looked at Remington's 700 SPS Varmint with heavy barrel ?

You can reach the ammeter wires by reaching up under the dash.Before you reach up in there, check with a flashlight for creatures. Mine was full of black widow spiders.

It would be nice if you could start at the surface and keep adding jts. of pipe until reaching bottom. Unfortunately, it's not that easy in water a mile deep. That pipe string would look like a rope blowing in the wind, what with the currents and stuff. They say the pressure now is 6700 PSI and...

I've got a 72 swinger ,340, with original wiring harness. If I install new wire with fuse from the alternator output to the battery stud of the starter relay,do I also leave the original wire on the alternator output ? Can one simply cut the original ammeter wires before going through the...

My mom and dad got married young, had 2 boys and 2 girls. My dad was never around after I was about 9. Mom took us all to church. We never had a lot. I raised myself.

Have you sold these already?

Go to Mopar Action tech archives, article- disc-o-tech. Mr. Ehrenberg does a good job of detailing the installation of disc brakes.

A certain culture where one person goes for a doctor visit and they take a dozen or so kinfolks along( screaming kids and all) and take up all the seating in the waiting room.

For years I suffered with bowlegs, constant knee pain. I am 56. I had one replaced last march and the other last july.I would not hesitate to do it again. You will be thinking why did I wait so long and you will be back to a normal life again. Good luck !!

Can anyone tell me if a 6" or 7" magnum 500 will fit front of 72 Swinger with 225/60/15 tire ?

On a 72 Swinger,with 73 disc brakes with BBP,will a 225/60/15 tire fit on front of car with a magnum 500 wheel that is 6" wide with 4" backspace, or would it be better to run a 7" wheel with 4 1/4" B.S. ?

I've got a 69 340 engine in a 72 Swinger w/ 727 trans, 72 340 exhaust manifolds.I bought 2 1/2" exhaust pipes from TTI. The driver side pipe is a close fit between torsion bar and floor, so close I had to deform the pipe a little so it woud not rub on top and bottom. Anyone else had this...

I had a shaft shortened for my dart. A few inches on one end is a smaller O.D. Does it matter on which end the smaller O.D. is installed ?

Hello Dart 74. The mopar chassis book says measure the length with the axle in the as raced condition (the car on its wheels and at raced weight).The drive shaft length from the center line of the front u-joint to the center line of the rear u-joint should be 3.5 inches less than the measurement...

I've got a 72 Swinger with a 340 , 727, 8 1/4". I had a drive shaft built at machine shop. The shaft came back too short. I've got a 72 scamp parts car I could use the shaft and have it shortened. The only thing is the original shaft is about 3 1/8" diameter at largest part. The scamp shaft is...

I'm looking for 4 nice center caps and retainers for magnum 500 wheels. Please PM or answer here. Thanks.

Were there any washers (how thick ? ) used with factory bucket seat installation on the interior side ? This is a 72 A body.

I would like to buy a nice rear bumper for 72 swinger,also looking for 4 nice arm rests in white.I'm located in West Texas. Respond here or P.M.

I made a pattern from cardboard.Went to the local glass shop and bought a piece of 1/8" plexiglass. Cut it to fit with a dremel tool,covered it with headliner material from upholstery shop.Turned out nice.

What about your gasoline, is it fresh , clean ?

The temperature hit around 103 today (West Texas) with 65% humidity this morning. Worked in the shop ,building and installing package shelf in swinger.We had thunderstorms in the evening with showers.

Where is this location ? I live about 100 miles south of Lubbock .

Has anyone ever installed a "T" handle shifter with their factory A body console ? (automatic) I know the factory didn't make one, but I think they look better than the original shifters. I bought one from Duncan Motorsports but it doesn't shift very well.

Thank you 74 sport, I will check it out !