Search results for query: *

Have a list of things that need to be done to it for it to be finished?

Hey all. I have some questions for you guys. I posted in the forced induction spot first but thought maybe I could get some info here as well. I am finally going good on my 70 Roadrunner resto mod and most of exterior bodywork is done and I'm ordering the full cap stiffening kit and spring...

Hey all. I have a few questions for you guys not sure if it needs to go here or in the new hemi spot but I figured I would start here and post it there as well. I am finally going good on my 70 Roadrunner resto mod and most of exterior bodywork is done. I'm going to be using a 5.7 hemi from...

And I'm pretty sure it's a 904. When I got it and changed the filter and pan gasket I took them to the parts store. "A reputable one". And matched up the gasket and filter to a 904 which is what it also stated in his book.. What would be any difference in the other ones? I think I'll unhook the...

Thanks all, I'll start digging into it. Yes, reverse seems to work fine and 1 to 2 shift seems ok also.

I haven't at all. I haven't been driving the jeep to long. You think That would cause my problem? Any insight on that? Thanks.

Hi all. I thought I would try with everyone here before I got to digging into this real deep. I have an 89 YJ wrangler with the 4.2 6 cyl and 904 auto, dana 30,ford rear 8.8 , and 35 inch tires... I am having an issue with the trans that I am having problems diagnosing. it is basically a...

Other one

I have 2 overdrive 4 speeds for sale. I think they are from trucks but can be made to work on anything. They both go in gears and input and output turn. Both look to be in good shape. 1 has everything on it including shifter, shift box, mount, rods and levers... The other one only has the levers...

360 magnum engine sold. Big Block 727 sold. clutch shaft service kit sold clutch rod kit sold. 9" z bar sold.

Pretty set in the EFI...

That was kind of my thinking... If I'd does have skim, I can just get it takes out?? I had planned on having it tuned or using a diablo or something else.

Hey all. I will be doing a 5.7 swap into a 70 roadrunner and have some questions and need opinions or insight.... I am about to buy an engine and have it narrowed down to 2. I can buy an entire wrecked 04 2 wheel drive crew cab Ram for $3500. Or I can get an engine, tranny and wire...

Yes it's still available. 1 hour south of St. Louis

and more stuff yet. rods seem to be kind of a cobbled up set, look to be a body. super shifter box is in unknown condition.

more stuff

hope this works better

Well that didn't go as planned, I'll have to resize them

Ok I have had a few questions about the "misc 4 speed linkages and stuff" hopefully these pictures will post.

94 or 95 Ram truck is what the magnum came out of

I have a few engines for sale as I am trying to make some room. 360 magnum engine complete and together I bought it for a project and was guaranteed it would run, but I didn't get to hear it run before pulled. I sold the project I was going to put it in and it has been on an engine stand in...

Hey guys, I posted this on fbbo but I know there is a lot of info over here. I have a 70 roadrunner project and am researching a 5.7 / 545rfe swap. I know that I'll have to do some tranny tunnel surgery but I have a few other i am most likely going to stick with the stock style suspension...

Yes, it has a clean clear title in my name. Here are pics of the interior.

71 scamp. I bought from a member a few years ago... I got deployed after buying it and since I have returned home I really haven't been able to enjoy much. So I am putting it up for sale. I'm really wanting to get into a 70 B body or an ebody. It is a nice cruiser or street & strip car.. It...

Ok, so I got some cup tip set screws a while back and drilled them for .031s' I put them in and drove around and still getting a slight stumble at cruise 2500 ish. I disconnected the secondary linkage to see what would happen cruised around and the stumble seems very slightly less. while I had...

That is very possible. I haven't gotten a chance to check everything out yet. I think it's something of what your talking about. At operating temp at idle it's right at or under 15 on my gauge. When I drive it, it will be fine for a bit and then get erattic . It seems to jump up when you get on...

Any idea why a new 1 wire alternator would crap out the voltage regulator after only a month? I got one in from summit and installed it. I haven't been driving it that much. I was out driving and tinkering with tuning in my carburetor and it started charging 18-20 volts all of a sudden. So, I...

I just drilled the old ones out slowly to the depth that they were and them tapped them ... After doing some research on the old interweb.. I pretty much figured out/ or at least see that everyone else that has done this use the set screw type.

Hope this uploads

Help, and question?! So, I got my idle feed restrictors in. But I think I may not have the kind that I need. I got the quick fuel brand which is a 6/32 but has a head with a flat screw driver slot. I got my old idle feeds drilled out and tapped for the 6/32 but when I screwed the new ones in I...