Search results for query: *

I would like to get $100.00 plus shipping , they ran quiet when switched out for 355s. Any questions pm me. I also have large yoke if interested for additional $25.00.

I have a set ring and pinion 4:10 for a 8 3/4 rear 742 case, also have the large yoke. $225.00 shipped in the USA.

I just got this in on trade for some other parts, I did clean it up a bit and paint it black. I was told it came out of a 70 dart. Measures 52 5/8 from flange to flange. $250.00 PLUS shipping. Please pm me with interest or questions thanks fabo

This is an 8 3/4 rear end housing. Measures 52 5/8 flange to flange, and 43" center of pedastool to pedastool. Asking $250.00, not sure how to ship but if it can be done i will try. Please PM with. Interest. I work 12hr nights so it may take a couple hrs for reply. Thanks.

Looking for the rear section, it ends about half way up the door, I would like a rust free entire rear section. Please pm me. Pics would deff. Be a plus. Thanks dustin

i have been doing my research for putting a 1998 5.9 motor and trand frm a ram into a 68 barracuda, I want a gd driver, PS,PB EFI and trans with OD. i noticed that booth of these companies are located in Mesa Arkansas. strange i thought. I am leaning towards hotwire since they are more into...

i have a line on a 96 dodge truck with 5.9 but i have heard ODBII is better and i thin that started in 97 or 98, just wondering how it is better and if i should try and buy the truck, want to repeat BADASS's build and put the entire setup in to a 68 cuda, truck is suppose to be around $600 to...

i have 3 of the 4 pieces, all are in nice shape, no creases on any of them. asking $200.00 for all plus shipping. PM me with interest. thanks fabo.

Cleaned these up with a wire brush and coat of black paint. Take $60.00 For the top set and $50.00 For the bottom set, plus shipping. PM me with interest. Thanks FABO

This is from a sure grip unit that I switched over, ran quiet in car. $50.00 Plus shipping. PM me with interest

Pulled from my friends 71 charger, talked his wife into a 500 something stroker, motor ran fine when pulled, just wanted bigger.Take$400.00. also gonna see if he will talk to my wife cause he must be better at this than me. Pm me with interest.

Just pulled these from a 383 that was in my friends 71 charger, he decided to build a stoker, his wife is way more understanding then mine.lol. i got the old motor for helping. This motor ran fine when pulled. Take $250.00 For the pair.

This is from a 67 barracuda, these will need cleaned and have some areas that need some attention. NO CREASES in these. I would like150.00 Shipped in the US. Please PM with interest

This is a pan that works with putting a big block into an body car. It is in good shape asking $75 plus shipping. Please PM with interest.

these have the tires on still, not sure how gd the tires are. 2 are wider 10" for the rear and 2 narrower 7" for the front. i can deliver to carlisle w/o the tires( i have a small car) $200.00, please pm with interest.

these ran fine with no noise when i switched to 3:55 instead. $75.00 plus shipping.please PM me with interest.

ran good when taken out of car. has 276 gears in it, $350.00 i can deliver to carlisle on saturday, or ship it weight 81 lbs just fyi. thanks FABO.

This is a 699 oil pan from a c body car, this pan works for putting BB motors into A body cars. $75.00 Plus shipping, please PM with questions or interest.

This is a manual steering box from my cuda, I am going with power steering so I have no need for this. $75.00 Plus shipping, please PM me with questions or interest.

Same as the other piece, Gd driver qquality, no creases, could use a polish. $100.00 Plus shipping PM me with questions or interest. I will sell as a lot or individually

This is atleast Gd driver quality condition, could use a polish, no creases, this fits fastback only! $100.00 Plus shipping, will package with others listed or sell individually. Please PM Me with questions or interest.

This piece has some bad spots (pictured) someone could repair these but I am not skilled in that. For fastback only. $25.00 plus shipping. PM with questions or interest

This is the upper right rear window molding for 68-69 fastback only cuda! I would consider this to be atleast Gd driver quality, could use a polish for sure, no creases anywhere. Please PM me with questions or interest. $100.00 Plus shipping, will combine if you buy booth pieces

This is the left upper piece of trim, I would consider these at least Gd driver quality. Could use a polish. I would like $100.00 Plus shipping please PM with questions or interest. These are for the fastback only!

just as the ad says, i bought these for my 84 dodge tuck but the heater box sticks out to far, just dnt have the clearance needed. $100.00 plus shipping. thanks again

i have a 187 oil pan for sale. gd shape. $75.00 plus shipping

Just as it says, shipping to 15552, thanks

This is a fan I bought from another member, decided to stay stock instead.$25.00 plus shipping. PM me with questions or interest. thanks FABO.

Really nice and straight pieces, i will look again but i saw no dings or dents. Please PM with questions or interest. Thanks FABO. $150.00 plus shipping.

Out of 340 motor. Please PM with questions of Interest. Thanks. $40.00 plus shipping.