Search results for query: *

Thanks, but I'm not seeing the outer anchor nut or plate in either location on mine. I was concerned that the anchor may have been cut away and discarded when the tubs were installed. Possibly like Dana67Dart, although his is a ragtop. Ill take a pic and upload it.

Can someone please provide a picture of where the rear outer seat belt anchors belong on a 67 Dart GT. I am working with a car that was previously tubbed and am restoring it to mini-tub. Can't identify where the outer seat belt anchors should be.

Looking for a quarter panel plastic plug 1967 Dart OEM# 2783355

Beautiful ride! I am attempting to assemble my 67GT (finally). I have installed a swap meet K member and a 440,727, and 8.75. I purchased it for $500 as an empty shell. Inner fenders cut out for fenderwells and quarters mutilated for slicks. I have been in the process of restoring the sheet...

I am trying to resurrect a 67 GT that I purchased as just a shell of a vehicle. I'm not sure how the vehicle was originally equipped because I have seen either a finish panel or what I think is a four piece upper and lower molding/trim set that "connects" the tailamps.

1967 Dart GT trunk finish panel or moulding set

Does anyone know the part number or supplier of high quality 7260 U joint straps?

STill hoping to get the part number to good quality 7260 u-joint straps if anyone knows?

I am definitely interested if they are the correct braces. How do I send an image of what I am looking for?

In would like to purchase the two roof to outer wheel house braces if they are still available. See the image attached for a detailed request.

I am looking for rear roof to outer wheel house braces for a 67 Dart GT. Ill send pictures if you think you have them.

I need both sides roof to outer wheelhouse braces for a 1967 Dart GT. The previous owner hacked the braces out to install tubs. I am removing the tubs and restoring to the OEM configuration. I have attached an image of what the braces should look like, and an image of what's left of them in my...

charger426, I would like to know the vendor/manufacturer of the straps that you are using. I figured straps worked for OEM, as long as they are quality pieces I'm fine with them. I just don't want to trust my driveshaft to "cheap/low quality" straps.

mderoy340, Are you saying that instead of drilling the yoke you just fitted the girdles with hardware store bolts, no nuts? I was thinking of that but didn't know if it had been tried and proven.

I am told the OEM strap P4120468 is lo longer available. Can any one tell me if the NEAPCO 1-0023 strap is a reliable substitute component for a 450 HP "street car" with 10 inch tires? If there is a better option, please advise. I have looked at the Moroso girdles, but I dont want to drill...

I turned 0.085 from each axle and it all fits together like it should. Moral of the story; whenever possible, do it yourself!

Need the two floor anchors for the rear seat, 67 Dart GT.

I have a pair of buckets for my 67 Dart GT but the seat tracks and stand-offs are very rusted. What other vehicles can I get these from?

AJ/FormS, Thanks for the information. I took the center section back out this morning and re-installed the axles. With the adjuster out as far as it goes I couldn't fit the thrust spacer (one I have from the original open rear) in between the axles. It looks like I would have to take another...

Rear seat for a 1967 Dart GT. Decent front seat to floor stand-offs (tracks).

Thanks. The 1/4 inch number was what I suspected. The rear axle has been an ongoing problem. It came out of a an open diff C-body and I had it and the axles) narrowed. I picked up a swap meet sure-grip unit but it doesn't feel like its going together right. The axles don't feel like they are...

I have a foam gasket and a steel gasket. Which one goes where? Also, if everything was correct, what is the maximun axle end play I could possible get? I have none.

Still have the rear seat for sale?

If the seat is still available I want it!

What year Dart? Is the rear seat still for sale?

How much is the desired driveshaft end play on a 440, 727, 8.75 (4.10 gears) set up with SS springs? I am only measuring 0.450 inches and only want to have the driveshaft shortened once.

I understand. Thanks. I ordered the MP book from Mancini.

With Super Stock springs?

I know this is a lengthy post, but I need to do this correctly so I am asking for your help. I am about to weld the spring perches on a narrowed 8 3/4 sitting on SS springs. The more I read about it, the more confusing it becomes. Please tell me if I have this right: 1) Front and rear "working...