Search results for query: *

I have a 1976 Dodge dart sport slant six car factory disc brakes I am redoing the entire front suspension. The lower ball joints were purchased as a unit. Upon inspection I notice the surfaces where they bolt to the spindle is not machined flat on the mating surface. Anyone know or get these and...

Speedometer cable push on 7/8 62 inch length part #

I have a 1976 dodge dart sport with a 360 LA and 727 tranny. my question is what length cable and how did you route your cable. I have stock manifolds and the guys at the muffler shop apparently didnt check to make sure the cable was clear from the exhaust manifold. and fried my cable housing...

The front Tranny line on my 727 is right behind the shifter cable mounting bracket. has anyone else ran into this problem. I ordered a new set of lines pre-bent but it looks like I may need an an angled adaptor to clear everything. if anyone has any pics of there set up that would be awesome as...

I dropped a tiny nut down the air gap hole on my 360 LA Im sick about it where would it end up tried a little magnet but I dont want to make it go further. whats the solution. I'm sure im not the first knukle head to do this.

I have a 1976 dodge dart sport 360 LA 727 torque flight combo. Running stock manifolds purchased the drivers side off ebay see attached image. could some folks post some images from the bottom of how they ran there head pipe on the drivers side.

I have a 76 dart sport with a 73 360 LA paired with a 727 torqueflight transmission. My question is I have the stock tranny yoke and im getting a measurement of 47 1/2 inches from center of u-joint to u joint leaving some play for travel could probobably go to 47 tops. is this a common length...

Im putting a 360 engine in a 76 dodge dart sport. The manifolds I had both exit in the center and the drivers side hits the power steering gear box. Im guessing I need a manifold that exits the rear. Anybody know the part # for that manifold or if there is on that can bought new and if so where...

Does the cone side go towards the manifold or away from it?

I have a 76 dodge dart sport s/6 conversion with spool mount conversions to 360. My hedman long tube headers are hitting the drivers side steering gear box on the first tube preventing it from going foreward and up by maybe a 3/8 of an inch. also on the stock heads it appears the headder mounts...

does anyone have images of stock location of studs and where bolts go for a 72 360 with stock manifolds. I bought the factory correct bolt kit from mancini racing. there is also one bolt that has a double sided bolt that im not sure if thats for ground or what. it also had two thing taht look...

I Have a 76 dart sport with a 360 bored 30 over, rpm air gap intake, 600 edelbrock carb, 727 torqueflite tranny. Im Running hedman long tube hedders, and using the mancini racing kickdown cable with the BPE throttle cable kick down cable holder. I will probably not do a lot of racing but want...

I changed out the power steering gearbox on my 76 dart sport. the new box did not come with the the coupler that the return line attatches to it is held on by two 7/16 bolt and there are two rubber seals on one side and a spring inside not sure what this part is exactly called. My question is...

I changed out the power steering gearbox on my 76 dart sport. the new box did not come with the the coupler that the return line attatches to it is held on by two 7/16 bolt and there are two rubber seals on one side and a spring inside not sure what this part is exactly called. My question is...

I'm changing the power steering gearbox in my 1976 dodge dart sport power steering gearbox. I have the old one out but have run into a couple of problems. 1. does the pitman arm need to be pressed onto the steering box shaft? 2. Does the steering column need to be unbolted and pulled back to...

Im changing the power steering gearbox in my 76 dodge dart sport and am having difficulty getting the shaft into the steering link. Does the steering column need to be loosened and pulled back or do you just fight with it until it goes in? what is the trick?

I have 1973 360 LA engine out of a motor home freshly rebuilt. I am eliminating the air conditioning. The air conditioning mount was basically a piece of angle iron that ran across the top water pump bolts horizontally and the unit sat front and center. All that will be gone. So I am cleaning...

Do you have to turn the engine over to get the holes in the cam to line up when priming a 360 im sure there is some grease in those holes and even after running the drill for 3 minutes it does'nt seem to be getting up there. I know the pump is pumping because i made the bonehead mistake of not...

I'm installing an edelbrock performer RPM air gap intake manifold on my 1973 360 LA engine do the locating pegs on the front and rear of the block need to be removed? no decking was done during the machining process. The intake seems to be teetering on those pegs and also the instructions say...