Search results for query: *

Hey all Looking at rebuilding my 8.25 over the winter as it is on it's last legs...Since 8.75's are hard to find and expensive to rebuild I am going to stick with the 8.25 as is should hold up to my street only car. Looking for some advice on part manufacturers... Axles Looking at a set from...

Hey guys I have a 8.25 in my Duster and the axle bearing surfaces are a little scored. I used some repair bearings but it think it is time for some new axles. Where would be the best place to look for some new ones. Most of the big companies only have dakota or durango shafts. Can these...

Man sometimes I really have to wonder.....Went into my local Chrysler dealership and asked the guy behind the parts counter (who's been there forever) for a water pump gasket for a 360 LA engine.....The guy looks a me like I have two heads and asks what's an LA...I know it's been since 1992 but...

Looking for a 70 to 73 V8 discharge hose for use on my 73 Duster. I am swapping out the /6 for a 360 and can't make the original /6 discharge hose work (bends are all wrong). Original part numbers would be 3441517, 3441411, or 3502517. NOS or and easily restorable line would be great...

Looking for the bracket that bolts to the cyl head and the alt bolts into on a 70 up factory A/C car. Looks Like this Thanks Brent

Hi Guys I am swapping out my /6 for a 360. The engine I obtained had a 727 with it. I know if I keep the 727 I will have to shorten my drive shaft when switching from my current 904, but I have also read that the some of the column shift linkage parts will not fit right. Namely the cross...

I picked up a good federal pump with a bracket and integrated cooler today, but I still need the two triangular brackets that attach the pump to the block. It's a small block set up. The smaller of the two brackets has 2 45 deg bends and goes at the back of the pump. Even if someone has the...

I am swapping my 225 for a 360. The slant had a dual exhaust system with 2 inch pipe all the way back except for the mufflers which are 2.25 in and out. For the 360 I have 340 exhaust manifolds with 2.5 inch head pipes. My question is, if I keep the 2 inch pipe after the mufflers will it...

Looking for a small block V8 power steering pulley and bracket. I've got a good federal pump off my slant six but the pulley will by wrong for my 360 swap. If no one has a federal setup then brackets and a pulley for a saginaw would be fine, pumps I can get reman if need be. I am in...

Can't find this casting number. I just purchased a 360 with a 727 bolted up to it. There are the numbers 925-1 on the bell housing in big #'s then down on the side is 2466925-1 and A 727 A on the bottom of the bell housing. On the tail shaft there is 2466901. I found reference to the...

Looking for some sage advice. My 73 Duster with /6 just isn't doing it for me any more so I am looking at a V8 swap. I will be using the schumacher kit but I need to decide what engine to start with. The local wrecking yards have the following engines. 75 360 from a 300 series van, a 92 360...

Looking for a good used holley 8007 390 cfm carb. If you have a good rebuildable one laying around and the price in reasonable let me know. Thanks Brent [email protected]

Well I got my 73 duster after searching and searching for an old mopar that wasn't all rusted out. I live in Ontario, Canada and everything from up here is rotten. I had a 69 dart gt when I was sixteen and was looking for something to bring back some memories and to work on in my spare time to...

Hopefully a quick question. I am pulling apart my 73 Duster and found the multi connector from the ignition switch to the harness is burnt at the red ignition wire and the plastic connector is burnt and turned to dust when I pulled it apart. Looks like the guy's at the factory left a...