Search results for query: *

Just moved from St Louis to Eureka California. Since we were towing my Dart with 04 Ford F150 V6 we took the southern route since the mountains aren't as steep. The Ford lost the radio then speedometer about an hour and a half outside of Flagstaff, AZ. We had to unload the Dart to get parts...

I am looking for a map light switch for my 71 Dart. [email protected]

Looking for a front bumper for a 70 or 71 Dart

Is the 72 front bumper the same as the 71?

I am looking for right rear side tail light housing for my Dart. The car is all done the bumpers are re chromed but the tail light housing on the right side had a bulb rusted in place on the backup housing and it will longer hold bulb correctly. Anyone have one they are willing to part with...

I am trying to get the lock off the glove box, can someone explain to me how to remove it? Thanks!

I am trying to find a picture of the clips that hold the trim that runs from front tire to back tires under the door along the rocker. I cant find them for the life of me and want to order some new ones but I have no idea what the look like. Does anyone have a picture of the clips I need...

I almost have my car finished and just got my gauges and cluster back. All the gauges have been re calibrated and the amp meter has been converted to volt meter and a solid state voltage limiter is now being used. The speedo now reeds 150. I am thrilled to see it all finally coming together...

My 71 Dart came with electronic ignition, with the new motor I am going with the orange box electronic ignition. My question is, where or how to mount it. The factory ignition mounted with bolts on the corner left and right side of the box. The Orange box mounts on top and bottom. I am...

I am running a column shift 360/727 in a 71 Dart. The 71 has 73 and up steering link and steering box. Will the Dougs headers or TTI's work in this setup? Or better yet is anyone using them in a setup close to this? I am hoping to buy these today if possible.

I am looking for a little direction as far as air cleaners go, I know this should be a fairly easy choice but I am just not sure. I was looking at the black Mopar one that matches the valve covers. I noticed its 13 1/4, I didnt notice any replacement 13 1/4 air cleaners in the Summit catalog I...

Do the transmission likes have clips that hold them to the oil pan, engine block, or together? Or do they just screw into radiator and no clips?

I have changed my drive train from a 318/904 8 3/4 rear and 7260 yolk I have dropped in a 360/727 8 3/4 rear and 7290 yolk. Will the new driveshaft be shorter than the original one? And if so would you just have it shorten or would you have a new one made? Also anyone know what the...

I know when I took my master cylinder off there was a plastic gasket behind it. I am putting a Mopar Performance master cylinder and somewhere along the way I lost the plastic gasket. Does anyone sell these? This is for manual brakes. Thanks!

I originally bought this 71 Swinger with the intention of fixing what little rust there was. Which was about 2" of rust showing on both lower quarter panels and the passenger side fender has a little dap of rust on the bottom corner. The car also had alot of parking lot dings. The car had...

I am looking to buy a new idler arm and pitman arm and was on Rock Auto's website and noticed they show two different parts for each one. Can anyone tell me the difference in these? Here is the Idler arms The Pitman Arms

Is this a federal or Signaw?

I want to get the pulley powder coated but I am not sure if iits just a nut I can twist off or not. Has anyone take one off before? Also does anyone know if there is a rebuild kit for these federal pumps? I was thinking of having it powder coated also.....may have some more stuff for you Leanna

Someone told me a few years ago there was some that was taking vintage car radio and update them with new electronics and rcs outs. anyone know who does this??

Well my car is done with paint and im going to start putting her back together next weekend. I though I had a someone that was going to sell me a set with 3.23 gears...but thats another story. I'd like to have clutch style suregrip in 3.23 gears but will take 2.76, 2.94 or 3.55...

I own a 71 Dart that I am about 2 weeks or from putting back together. I just got new paint. I am replacing the entire drive train, which is where my question comes from. The original gas tank has the 4 vent tubes coming out of it. I am not using the original 318 engine and I am going to...

Looking for a set of motor mounts 340/360.... [email protected] or pm me here Thanks!!

I am looking for a 1971 Dart radio heater A/C bezel.

I am trying to get hole location for 70 Dart trunk emblem. I am assuming its not glued on. Do all the studs have nuts on them? My Dart is getting paint now and need to drill holes for emblem because the trunk lid is from 71 Dart. Heres a few pics of progress

I finally got around to sorting out my front end parts and decided to take some pics and before I got them all back together. I had these done by Phoenix Specialty Coatings and they turned out great. I had to take the lower control arms out in the sun to get a good pic of them. And these pics...

I am about a week away from needing to choose a color for my 71 Dart. The interior is in near perfect condition and is green, therefore my real only exterior color choice is green. The guy whos doing the final body work and paint was trying to talk me into a 1969 color of F6 Bright green...

I am in the process of installing my frame connectors from US Cartool. The only issue I am having besides a little trimming and grinding is figuring out how to route e-brake cable. Does anyone have pics of their install with the e-brake cable ran. Or can you tell me what you did? I know the...

I have a quick...do the direction of the front and back pivot bolts matter? Heres what happened, its been warm here in St Louis the last few days and I decided to install my new set of XHD springs. I got a new media blasting cabinet and blasted all the parts and painted them with zero rust...

I am getting ready to replace my axles and center section in my Dart. Should I look for a clutch type or cone type sure grip. I have heard the cone type are stronger but the clutch type are rebuildable. Any help is greatly appreciated!! Thanks and happy holidays!!

Well I meet Ken Hensley a couple years ago at a Mopar show, Monster Mopar, and was really impressed with his knowledge and expertise. I hunted down thier booth this year with plans on buying this 318 kit they sell, which included heads, intake, cam and 4 bbl carb. The more I though about the...