Search results for query: *

You could make an extension cord and use the dryer plugin in the house. If it has one.

Have you sold the carb?

How much for the crank and rods? Jim

What were your results? ET & MPH

I think you would be OK on the pump,if it's alcohol compatible. Be sure to vent both valve covers or you will be replacing main seals. DAMHIK

Mike, find a late 70 or early 71 360 block. They should take at least a .070 overbore. The have the 360 crank off-set ground to 1.85 on the rods. Should get you real close to 400 incher. Don't know how long the crank would hold up. Would an aftermarket crank for the block be acceptable? Jim

Mike, just read this. Congrats to Parker on a great driving job. And Kudo's to crew chief as well. Jim

Hope those who can will come. This is a fun event good racing and swap meet. Also a car show. http://www.mokandragway.com/pdfs/mopars_2015.pdf

That is good to hear Mike. I guess you got the head repaired or replaced? Jim

Might also be a coil heat soaking.

Used SB Molodon oil pan for 318/340 mains. It has been modified for header clearance. I have used TTI, Hedman and Hooker's with this pan. It has been repaired. The pickup tube broke off and the crank knocked it around. The pickup tube was repalaced and has about 50 runs on it. $75 + frt PM me...

I use that cam in my 416. 72cc W2 open chamber heads, Wiseco flat top pistons zero deck height, 1.6 rockers. I have .085 piston to valve clearance on the intake and a little over a .100 on the exhaust. With a .039 gasket. The cam is installed a 108* also. Aren't 63cc heads closed chamber? You...

Mallory Hyfire 6 plus matching coil and Unilite distributor. $200 + frt. PM me here.

Sold pending receipt of funds. Jim

NIB MP 4" stroke forge crank for 318/340 mains. Part# P5007252 $650 + frt from 74354. PM me here. Jim

From the inside of the top to the gskt flange is 3". I would sell this set for $225 + frt from 74354. Jim

I have a NIB set @ home. Will measure them tonight. Also they can be had for less $$. Jim

I had to put the oil slinger back in mt 416 after switching to alcohol. The switch caused it to puch the front seal out.

You might try a 2000 Durango 360 dipstick.

Sold.

Still for sale. Joplin MO 64801 Cell# 417-317-6863 Jim

I prefer the Clay Smith mechanical. No electrical draw. My car runs 10.5's with this setup. I have a friend who has been in the 8's with a rat motored digger on alcohol with CS pump. JMO Jim

Sounds like a low 10 sec ride. I'm sure he'll do well. He can definitely drive.

Congrats Mike. Parker must have really been on his game. What is this second car you speak of? I have not heard about it yet. Jim

69 Dart 2DRHT strip/street rolling chassis. 8 point mild steel cage rear factory frame rails have been moved in 3.75". Sub frames are tied. Narrowed Dana 60 with Strange spool and Dutchman axles. CalTrac rear suspension split mono-leafs and bars. Rancho 9 ways on the rear and QA-1 12 ways on the...

Sale pending

Thanks I fixed it. Jim

That is correct. 3000 lb A body.

C&S aerosol 900 CFM alcohol carb. Very responsive carb. $450 + frt. PM me here. Jim Joplin MO 64801

950HP Pro Form gas carb. Billet baseplate and metering blocks. Also has 50cc pumps on both ends. $425+ frt. PM me here. Jim Joplin MO 64801